Manual Felisatti RF67 (page 5 of 33) (English, German, French, Italian, Portuguese, Spanish)

502507

Zoom out

Zoom in

1/33

1.1. Loosening the locking wing nut G will release the

depth stop E, facilitating simple stop adjustment.

Adjust the required depth using scale Y with the

depth adjustment handle N, tighten the locking wing

nut G, fine adjustment is obtained using the fine

adjustment handle M.

1.2. The depth of the cut can also be adjusted with the

handle C, turning it clockwise to increase depth and

counter clockwise to reduce.

Fixing lever H should be pressed to immobilize the

machine at a determined working height.

To prevent running off-load, rotate the depth adjustment

handle N and C until the desired return distance is

obtained.

With the stepped stop F it is possible to perform the

milling operation in three stages. To start, adjust the

milling depth to the lowest position of stepped stop F.

Then the milling operation can be carried out at the

higher positions.

PRECAUTION: For large diameter cuts, it is recom-

mended that the depth is set to minimum and to con-

tinue cutting in stages.

When commencing the work, the milling head should be

slowly entered until the desired depth is obtained and

then allowed to advance, always supporting the machine

with two hands.

OPERATING INSTRUCTIONS.

PRECAUTION: The machine should always be

unplugged before making any adjustments to the

machine.

WARNING! The actual milling operation should always

be made in the direction opposite to the milling head

rotation direction (according to Fig. 4). Advancing the

machine in the opposite direction could cause it to

rebound and lead to an accident.

1.1. Milling

1. The milling depth should be adjusted in accordance

with the previous description.

2. Switch on and place the machine over the work

piece, firmly held in place.

3. Carry out the milling operation with a uniform ad-

vancing movement.

4. On completing the milling operation, push the upper

section of the machine upwards and switch it off.

1.2. Milling with parallel stop

To install the parallel stop and with the guide rods in the

base plate P and held in place with the wing screws V

according to the required measurement.

Once both wing screws V have been loosened, the

parallel stop can be re-adjusted using fine adjustment S.

Adjust the desired length with the divisions with inches

and millimeters marked on the side stop I.

Stop strip T may be used to increase the parallel stop

contact surface.

1.3. Milling with the copier bushing

Copy bushing U enables edges to be milled on the work-

piece in accordance with a pattern or template.

Installing the copier bushing

In order to use the copier bushing U, it must be installed

on the lower section of support plate P from above and

fixed in place with the screws.

WARNING! It is essential to ensure correct installation

position.

1.4. Milling straight or profiled edges

When milling straight or profiled edges, without the

parallel stop, the milling head must be fitted with a guide

shaft or ball bearing (optional accessory).

The operating machine should be brought into contact

with the work-piece from the side, until the milling head

guide shaft or ball bearing is seated against the edge of

the work piece. The machine must be guided with both

hands, always perpendicular to the surface, along the

entire length of the work-piece edge. Excessive applied

pressure could damage the work-piece edge.

DUST EXTRACTION

WARNING! Always make sure that the tool is switched

off and unplugged before fitting or removing any dust

extraction device.

Dust extraction keeps the workplace clean, prevents

dust build-up in the air and facilitates waste elimination.

These milling machines are fitted with adapter, which

can be coupled to a universal vacuum aspirator or other

dust suction device.

CAUTION: A suction extractor should always be used

that has been designed in accordance with the applica-

ble directives in relation to dust emission when milling

wood. The flexible hoses of conventional vacuum clean-

ers fit directly onto the dust extraction nozzle.

Installing the dust suction adapter

PRECAUTION: Before installing the suction adapter K,

press the fixing lever H so that the upper section of the

machine ascends to the upper position.

In order to install the dust suction adapter K, it should

be inserted in the square opening on the base plate P

until it fits fully into place, and then fixed using the wing

screws R, which are located on both sides of the

adapter K.

In order to maintain optimum chip extraction, the suction

adapter K should be periodically cleaned.

The aspirator should be suitable for the material being

worked.

A special aspirator must be employed in those cases

where dry harmful or carcinogenic dust is produced.

In situations where prolonged wood operations are

performed or machines are used industrially with

materials that produce dust that is harmful to health,

the machine must be connected to a suitable external

aspiration device.

MILLING MACHINE ADAPTED TO A WORK TABLE

1.1. Assembly of the milling head (Fig.7)

WARNING! The mains cable must be removed from the

socket before any adjustments are made to the machine.

It is recommended that protective gloves be worn when

installing or removing milling heads.

1. To assemble the milling head, turn the depth handle

W until it stops, turn the clip-holder shaft to match up

the axis groove with the blocking button B.

2. A spanner should be used to loosen clip fixing nut D

in an anticlockwise direction.

3. Insert the milling head so that the shaft enters the

clip by a minimum of 20 mm (shaft length).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti RF67 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Felisatti RF67 Manual

Product: