502507

Felisatti RF67 Manual

3
Zoom out
Zoom in
Previous page
1/33
Next page
TECHNICAL DATA
Milling machine RF67/2200VE
A
bsorbed powe
r
W 2200
No load speed rpm 12000-21000
of milling cutter attachment
mm 12
Machine weight (without accessories) kg 5.9
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual. Any other use
of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
A Safety push button switch (Fig.2)
A1 On-/off switch (Fig.2)
B Blocking button of the clip-holder shaft (Fig.1)
C Depth adjustment handle (Fig.1)
D Clip fixing nut (Fig.1 and Fig.2)
E Depth stop (Fig.1)
F Stepped stop (Fig.1)
G Locking wing nut (Fig.1)
H Fixing lever (Fig.2)
I Side stop (Fig.3)
J Transparent frontal protection (Fig.5)
K Dust suction adapter (Fig.6)
L Speed adjustment (Fig.1)
M Fine depth stop adjustment (Fig.1)
N Depth adjustment handle (Fig.1)
O Grips (Fig.1)
P Base plate (Fig.6)
Q Sliding plate (Fig.2 and Fig.3)
R Wing screw for dust suction adapter (Fig.6)
S Strip stop (Fig.3)
T Parallel stop fine adjustment (Fig.3)
U Copier bushing (Fig.3)
V Wing screw (Fig.5 and Fig.6)
W Depth adjustment handle (Fig.2)
Y Depth adjustment scale (Fig.5)
EQUIPMENT
- Side stop
- Clip, 1/2” and 1/4”
- Fixed spanner, 22 mm and 7 mm
- Transparent guard
- Dust suction adapter
- Copier bushing
- Operating instructions
- Safety instructions
- Warranty
SAFETY INSTRUCTIONS
See “Safety instructions” enclosed manual, supplied
together with this instruction manual.
WARNING! The dust produced when milling asbestos
and/or silica stone materials is dangerous to health.
Follow the insurance company’s safety instructions
regarding the responsibility of employees.
For your personal safety, always connect the machine
to a mains supply by a differential and thermal cut-out
switch, in accordance with regulations on low-voltage
wiring sitemaps.
Do not perforate the machine casing, as this would
destroy the protective insulation (use adhesive labels).
Always unplug the machine before doing any work on it.
Always stop the machine by switching it off, not by
unplugging it.
WARNING! Before each use, inspect the plug and
lead. Should they need replacing, have this done by an
official service centre. Only plug the machine in when it
is switched off.
Always keep the lead out of the machine’s working
area.
Only plug the machine in when it is switched off.
Do not allow the machine to get wet, nor should it be
used in wet environments.
When using the machine, always wear safety goggles,
gloves and non-slip footwear, and it is advisable to
wear ear protection.
Check for correct piece fixing before commencing any
operation.
Only milling heads with acceptable revolutions that are
at least the same as the maximum off-load revolutions
of the machine should be used.
The milling head shaft diameter should match the
inside diameter of the tool-holder (locking clip).
It should be ensured that the milling head is firmly held
in place before the machine is operated.
The clip-carrier shaft support lever must only be oper-
ated when the machine is stopped.
The milling head should only be brought into contact
with the work-piece after it has been switched on.
The machine must be firmly held by the grips. Other-
wise the recoil produced could cause the machine to
work imprecisely or even dangerously.
Hold the machine firmly in both hands and in a stable
position.
During use, it should be ensured that the milling head
is in the centre of the copy bushing in order to prevent
any personal injury or damages to the work-piece.
The milling machine must never be used on metal
objects, such as nails and screws.
Hand must be kept clear of the milling machine while it
is operating.
The cutting depth must never be adjusted with the
motor running. A mistake in this time could lead to
personal injury and/or damage to the milling head or
work-piece.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti RF67 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti RF67 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info