Manual Felisatti PF102 (page 4 of 24) (English, German, French, Italian, Portuguese, Spanish)

502500

Zoom out

Zoom in

1/24

OPERATING INSTRUCTIONS

1. Planing depth

WARNING! Always unplug the machine before carrying

out work on it.

Regulate the cutting depth, from 0-2/2,5mm. without

gradations, turning the handle K. Fig. 1, making out the value

in the scales J and H.

2. Surface planing

WARNING! The plane should only be applied to the work-

piece in the switched-on position.

Position the machine with the front section of mobile plate

S over the work-piece. During surface planing (wood beams

and tables etc) mobile plate S and base plate U should

always rest on the entire work surface (danger of blade

repercussion). The blade should be guided with both hands

and moved forward in a uniform fashion over the work

surface.

For surface planing a shallow cutting depth is recommended,

repeating the process several times.

3. Canting off edges

Guide slot P, located in the centre of mobile plate S, enables

fast, simple edge canting off to be carried out on the work-

piece.

The plane should be placed with guide slot P over the edge of

the work-piece and then guided along its length. A constant

angle of 45º should be maintained during this operation,

together with a uniform advance movement.

4. Carrying out routing and bevelling

- Depth limit N

The assembling must take place at the right side and the

depth reduction may be adjusted from 0 to 15mm.

In order to enable the reduction, it is important that the blade

should be ranged well sideways with the side level of the

mobile and xed bases.

- Side limit L

The side limit L may be adjusted at both sides of the plane,

keeping it immovable by means of the control I.

In order to assemble the lateral stop, rst place the set square

V and x it with wing nut I (Fig. 1).

Place the lateral stop L, put the nut on the hexagonal slot

of the upper part of set square V and x it with wing nut W

(Fig. 1).

In order to disassemble the lateral stop, follow the instruction

in a reverse order.

In order to adjust the lateral stop, loosen wing nut W, move

the side stop in order to achieve the desired measurement

and again tighten wing nut W.

Using depth end-stop N together with side end-stop L permits

routing operations.

5. Support foot D

Support foot D should always be installed and allows the

machine to be rested on a surface immediately after use

without any danger of damaging the workpiece surface or

the blades.

When using the machine, support foot D is folded backwards

leaving the rear plane surface free.

PARTS REPLACEMENT

1. Blade replacement (Figs. 3)

WARNING! Only hard metal blades may be used with this

tool.

It is tted with hard metal blades when it leaves the factory

. When blade replacement becomes necessary, both should

be replaced at the same time. Otherwise, the lack of balance

could lead to vibration reducing the lifetime of the tool.

The blades of hard metal have two rows of edges and may be

converted or changed without having to be adjusted. In order

to convert or change the blades, just screw off by one or two

turns the screws O and with a pointed piece of wood, take out

sideways the blade.

Before reassembling again the blade, clean the carrier or

guide of the blade, making sure the carving of the blade and

the guide rule t correctly.

Adjust the lateral position of the blade to the level of the xed

and mobile bases by means of a wooden strip, Fig. 3.

Tighten again the three screws O.

PRECAUTION: Jagged or worn blades cannot be

resharpened and must be replaced.

2. Toothed belt replacement (Fig. 4)

The procedure for replacing the toothed belt is described

below:

1. Loosen screw R and remove toothed belt cover Q.

2. Cut the toothed belt with shears or a knife and remove it.

3. Before installing a new toothed belt, thoroughly clean

pulley G and drive wheel E.

4. Install the new toothed belt on drive wheel E and press it in

place, while rotating large pulley G at the same time.

5. Replace toothed belt cover Q and x it in place with screw

DUST EXTRACTION

WARNING! Always check that the machine is switched

off and unplugged before removing or installing any dust

and sawdust suction device.

Dust extraction keeps the workplace clean, prevents dust

build-up in the air and facilitates waste elimination.

These plane have a chip expulsion hole M to which adapter T

may be connected. A universal vacuum cleaner may be tted

or any dust extraction device.

PRECAUTION! During prolonged operations with wood

or in professional applications with materials that

produce harmful dust, a suitable external aspirator must

be connected.

ACCESSORIES

Accessories and their corresponding order number can be

found in our catalogues.

MAINTENANCE AND CARE

WARNING! Always unplug the machine before carrying

out work on it.

- Blade inspection: Excessive forward movement will

signicantly reduce machine power and blade life. Sharp

blades will permit a high cutting capability and increase

machine life. Blades should be replaced according to

requirements.

- Inspect the mounting screws: regularly inspect all the

mounting screws and ensure they are rmly tightened.

Should any screw be loose, tighten it immediately. Failure to

do so could put you at serious risk.

- Motor maintenance: always take the greatest care over

this and make sure that the motor winding is not damaged

and does not become wet with oil or water.

- The vents should always be kept clean and free of

obstacles.

- Clean the machine thoroughly after each use. Blast the

motor regularly with compressed air.

- Check that the mains lead is in good condition. If it is not,

take it to an Ofcial Service Centre to have it

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti PF102 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,76 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Felisatti PF102 Manual

Product: