502500

Felisatti PF102 Manual

3
Zoom out
Zoom in
Previous page
1/24
Next page
3
TECHNICAL DATA
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at hand to
use when carrying out maintenance on the indicated parts.
If the tool is used with care and normal maintenance is carried
out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the
tool is strictly forbidden.
PLANER SAFETY RULES
Planer Safety Rules
- Wait for the cutter to stop before setting the tool down. An
exposed cutter may engage the surface leading to possible
loss of control and serious injury.
- Do not reach into the saw dust ejector with your hands.
They could be injured by rotating parts.
- Apply the machine to the workpiece only when switched on.
Otherwise there is danger of kickback when the cutting tool
jams in the workpiece.
- When working, always hold the planer in such a manner that
the planer base plate faces at on the workpiece. Otherwise
the planer can become wedged and lead to injuries.
- Never plane over metal objects, nails or screws. The planer
blade and the blade shaft can become damaged and lead to
increased vibrations.
- Secure the workpiece. A workpiece clamped with clamping
devices or in a vice is held more secure than by hand.
- Never use the machine with a damaged cable.
Do not touch the damaged cable and pull the mains plug
when the cable is damaged while working. Damaged cables
increase the risk of an electric shock.
Products sold in GB only: Your product is tted with an BS
1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug tted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or less.
ILLUSTRATIONS
DESCRIPTION (See gures)
A Safety push button switch (Fig. 1)
B On-/off switch (Fig. 1)
D Support foot (Fig. 2)
E Drive wheel (Fig. 4)
F Toothed belt (Fig. 4)
G Idler pulley (Fig. 4)
H Vertical depth graduated scale (Fig. 2)
I Side end-stop immobilisation control (Fig. 1)
J Circular depth graduation scale (Fig. 1 and 2)
K Depth graduation handle (Fig. 2)
L Lateral stop (Fig. 1)
M Sawdust extraction (Fig. 2)
N Cope depth end-stop (Fig.2)
O Blade replacement screws (Fig. 3)
P Guide slot (Fig. 1)
Q Toothed belt cover (Fig. 4)
R Toothed belt cover screw (Fig. 4)
S Mobile plate (Fig. 2 and 3)
T Dust suction adapter (Fig. 1)
U Base plate (Fig. 1 and 3)
V Side stop locking set square (Fig.1)
W Side stop regulation of the wing nut (Fig. 1)
Y Depth stop xing wing nut (Fig. 2)
EQUIPMENT
- Dust suction adapter
- Hexagonal key
- Lateral stop
- Depth end-stop
- Operating instructions
- Safety instructions
- Warranty
BRIEF DESCRIPTION
This tool has been designed to rout wood and similar
materials, to plane irregular surfaces and to cant off edges.
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage is correct:
it must be the same as that on the specication label.
Machines with 230V can also be connected to a 220-V mains
supply.
START UP
WARNING! Only plug in when machine is switched off.
Press the locking button A, and squeeze the trigger in the on/
off switch B. When the on/off switch is released, the machine
stops.
For safety reasons, it is not possible to lock On/Off switch
B, instead it has to be pressed while the machine is being
used.
CONSTANT ELECTRONICS (Mod. PF102/1100VES)
The built-in module permits:
- Soft start.
- The maintenance of a practically constant rated speed
up to rated power.
- An overload protection system by means of current
cut-off in the case of motor overload, in which case the
burring machine shuts down and re-starts when the grinding
pressure has been reduced.
Planes PF82/710 PF102/1100VES
Absorbed power W 650 1100
No-load speed /min 14000 11000
Cutting depth mm 0-2 0-2,5
Total cut width mm 82 102
Rebate’s depth mm 15 15
Approx. weight (without accessories) Kg 3,5 3,8
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti PF102 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti PF102 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info