723651
12
Zoom out
Zoom in
Previous page
1/13
Next page
21
22
1. Changing the RAID mode will cause data lost.
2. Please refer to the instructions when switching the RAID mode, otherwise the execution
might fail.
3. Interface of USB / eSATA can not be used at the same time.
4. When using RAID function, HDDs with the same brand, model and capacity is strongly
recommended.
5. When using RAID function, more than one HDD partition is not recommended.
6. Under Windows Vista / 7, users can enable GPT when initializing HDD with a total capacity
of more than 2TB.
7. Older OS may not recognize the device if you use a different operation system than
Windows Vista / 7. For more detailed information about GTP, please visit:
http://www.microsoft.com/whdc/device/storage/GPT FAQ.mspx
8. If users enable MBR by mistake, in order to clean the partition table, you have to switch to
another RAID mode and do the RAID mode switch all over again referring to Setup.
Then go back to the RAID mode you want, repeat the previous actions and enable
GPT when initializing HDD.
9. For Macintosh users: the total capacity of more than 2TB could be recognized only for the
operation system is 10.4.11 Tiger or later.
10. Do not connect the device to the SATA port on the motherboard.
Use SATA to eSATA PCI-Express or SATA to eSATA PCI add-on card, otherwise the
PC (Windows / Macintosh) may not recognize the device.
11. Rebuild time is based on the capacity, e.g. it takes about 1 hour for 200GB.
12. When the USB / eSATA cable is plugged out, the device goes to sleeping mode
automatically.
REFERENCES
Figure-1
14. If the noise is still present, you can change the fan with another identical fan
of size 80x80x20mm referring to Figure-1.
13. If there is noise with the fan, power off the device, unscrew the fan, take out the cover ,
clean the fan and assemble it back.
Black cableRed cable
Positive
(electrode)
Negative
(electrode)
15. Setting up motherboard's power management in S3 is recommended.
(For more details, please refer to the user guide of motherboard BIOS setting).
16. If the device takes too long to initialize, please check if the HDD is securely installed or
update the eSATA host driver version.
17. If the transfer rate is not normal, please check if the setting of SATA disk jumper
is 1.5 or 3.0Gbps .
18. If the fan stops working, turn off the unit and replace the fan.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fantec QB-X8US3R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fantec QB-X8US3R in the language / languages: English as an attachment in your email.

The manual is 7,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fantec QB-X8US3R

Fantec QB-X8US3R User Manual - German - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info