723620
22
Zoom out
Zoom in
Previous page
1/23
Next page
42 43
FANTEC QB-X2US3R 2-BAY 3.5" RAID FANTEC QB-X2US3R 2-BAY 3.5" RAID
12) faQ
1. Under RAID 1 mode, if one of disk is crashed, can the device rebuild
the data when I connect another new HDD?
Answer: Yes, the device would start RAID 1 rebuilding automatically
when you connect another new HDD. No extra setup or configuration
is needed. In order to start RAID 1 rebuild procedure, please execute
following points step by step:
- Turn off the device and remove the crashed/faulty disk.
- Please turn on your PC, connect the USB3.0 cable at first to the PC
and then connect the FANTEC QB-X2US3R to the USB3.0 cable.
Now power on the device.
- Put a brand new HDD into the empty rack.
- Within a few seconds both Status LED of the device start blinking to
indicate the rebuild process has been started.
- The speed of rebuilding is about 250GB/h, which means rebuilding a
disk of a size of 500GB will last about 2h minimum, maybe more.
- If both status LED shine steady blue, the rebuild procedure is finished
successfully.
IMPORTANT NOTE:
- To rebuild your data securely, we recommend a new HDD that has
same brand and model no. or a brand new HDD which is bigger
than the crashed HDD.
- Don‘t disconnect the USB Cable during rebuilding
or Power off the PC.
2. Can I copy data to the disk during RAID 1rebuilding?
Answer: Yes, you can but it is not suggested doing that, and it would
extend the time of rebuilding.
3. Under RAID 1 mode, if one disk crashes, can my PC read the other
disk correctly?
Answer: Yes, the PC still can access to the healthy disk. If you want
to be sure your data are safe, you make a backup before starting
RAID 1 rebuild procedure.
4. How can I protect my data if the FANTEC QB-X2US3R crashes?
Answer: If your device is running in JBOD or RAID 1 mode, you
simply can remove the disks out of the device and connect them
to some other external or internal interface in order to access
you data. E.g. you can put the disks into an USB docking station to
backup your data.
If your device is running in RAID 0 mode, you have to replace the
crashed FANTEC QB-X2US3R either by a new or repaired one. Take out
both HDD and make sure to put the HDD 1 or HDD 2 labels on
corresponding disks. In this way you avoid to mix them up at upcoming
re-installation.
After your device is replaced, please connect the new (repaired)
FANTEC QB-X2US3R without any disks inside by USB 3.0 cable to a
running PC. Then set the QB-X2US3R to RAID 0 mode and press the
RAID mode confirm button until the device power off.
Now please, put the HDD 1 and HDD 2 into corresponding slots and
power on the device once again.
Now you should be able to access to your data without any data loss.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fantec FANTEC QB-X2US3R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fantec FANTEC QB-X2US3R in the language / languages: English, German as an attachment in your email.

The manual is 3,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info