58830
11
Zoom out
Zoom in
Previous page
1/12
Next page
EPSON Stylus Photo R300 Series
10/03 EPSON Stylus Photo R300 Series - 11
Cleaning the Print Head
If your printouts are unexpectedly light or faint, or dots or
lines are missing from the image, you may need to clean the
print head. This unclogs the nozzles so they can deliver ink
properly. Print head cleaning uses ink, so clean it only if
quality declines.
You can clean the print head either from the printer’s control
panel or using your printer software. To clean using the
printer software, the printer must be connected directly to
your computer (not over a network); see your on-screen
Reference Guide for details.
When you don’t turn on your printer for a long time, the
print quality can decline, so turn it on at least once a
month to maintain good print quality.
Follow these steps to clean the print head from the printer’s
control panel:
1. Make sure the printer is turned on but not printing, and the
red
b error light is off.
If the red light is flashing or on, you may need to replace the
ink cartridge; see page 9 for details.
2. Press the button to highlight
More Options, then press
OK.
3. Use the or button to highlight
Head Cleaning,
then press
OK.
4. To begin cleaning, press
OK.
While cleaning, the printer makes noise and you see a
progress bar on the control panel display. Cleaning takes
about 30 seconds.
Do not turn off the printer or interrupt the cleaning
process.
5. When the cleaning is done, run a nozzle check to confirm
the print head nozzles are clean.
Make sure letter-size plain paper is loaded in the printer,
then press
Stop. The nozzle check pattern prints (see the
next section for details).
6. If the pattern has gaps or missing dots, press
Stop to clean
the print head again.
If the nozzle check pattern looks correct, press OK to finish.
If you don’t see any improvement after cleaning three or
four times, check the solutions in your User’s Guide. You
can also turn the printer off and wait overnight—this allows
any dried ink to soften—and then try cleaning the print
head again.
Examining the Nozzle Check Pattern
Examine the nozzle check pattern you printed. Each staggered
horizontal and straight vertical line should be complete, with
no gaps in the dot pattern, as shown below:
If your printout looks okay, you’re done.
If any dots are missing (as shown below), clean the print
head again.
Aligning the Print Head
If your printouts contain misaligned vertical lines or
horizontal banding, you may need to align the print head.
You can align the print head either from the printer’s control
panel or using your printer software. To align the print head
from the printer software, the printer must be connected
directly to your computer (not over a network); see your on-
screen Reference Guide for details.
For the best results, load letter-size EPSON Photo Quality
Ink Jet Paper in the printer whenever you check the print
head alignment.
Follow these steps to align the print head using the control
panel:
1. Make sure the printer is turned on but not printing, and
letter-size paper is loaded.
2. Press the button to highlight
More Options, then press
OK.
3. Press the or button until
Print Head Alignment is
highlighted, then press
OK.
4. Press
OK to print the alignment pattern.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson Stylus Photo R300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson Stylus Photo R300 in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Epson Stylus Photo R300

Epson Stylus Photo R300 Quick start guide - English - 4 pages

Epson Stylus Photo R300 User Manual - English - 124 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info