708653
2
Zoom out
Zoom in
Previous page
1/3
Next page
Less Sensitive More Sensitive A
To mount the unit, first carefully drill out the required mounting holes that are marked on the rear cover
in oval shape. Next, using the rear cover as a template, mark the position of the drilling holes on the
wall. After drilling the holes, attach the rear cover to the wall using the included screws and wall plugs.
Adding the Home PIR Pet-immune Motion Sensor to the AG4000 Home Alarm System:
The alarm panel will group motion sensors and door/window sensors into 5 security types, each
assigned according to when they will be activated:
- Security Type “0”: Fully Armed. The sensor will be activated only when the system is in
Full Arm mode. This sensor will not be activated in Partial Arm mode. When the sensor is
triggered, the alarm will sound immediately without any preset delay.
- Security Type “1”: Partially Armed and Fully Armed. The sensor will be activated when
the system is either fully or partially armed. When the sensor is triggered the alarm will sound
immediately without any preset delay.
- Security Type “2”: Fully Armed + Delay. Same as Security Type “0”, except when the
sensor is triggered the alarm will sound after a preset Entry delay. This is mostly used for the
main entrance to prevent any accidental triggering of the alarm by the user.
- Security Type “3”: Partial Arm and Fully Arm + Delay. Same as Security Type “1” except
when the sensor is triggered the alarm will sound after a preset Entry delay. This is mostly
used for the main entrance to prevent any accidental triggering of the alarm by the user.
- Security Type “4”: 24Hrs intruder: The sensor will immediately trigger an alarm,
regardless whether the system is (partially) armed or disarmed. This is normally used to
protect areas from any unauthorized access, such as a safe box or an electrical maintenance
room, etc.
When a new sensor is added it needs to be assigned to one of the above security types.
To add the sensor:
1. Power on the sensor by inserting its battery.
2. On the alarm panel, enter the PIN + DISARM Key to disarm the system.
3. Enter your PIN + 15 + [security type number] + PARM to start the binding process. The
DISARM LED will start to blink for 30 seconds with a beep tone.
4. Within 30 seconds, set the sensor to enter binding mode using the tamper button shown in the
image on the first page.
5. When the sensor has successfully been added, the DISARM LED will turn on for 1 second
along with a long beep sound. A keypad LED will turn on to indicate the allocated zone number.
(Numbers 1 9 for zones 1 9, Number 0 for Sensor Zones 10 and above).
6. If the binding process fails, it will timeout after 30 seconds and 3 short beeps will be heard.
7. To exit the binding process, press the DISARM key.
IMPORTANT WARNING:
This package can contain small parts and/or material which can be dangerous to small
children! Be aware of this, and keep this away from small children!
For more information about the ELRO AG4000 Home Alarm System visit
www.elro.eu
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro AG40PP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro AG40PP in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro AG40PP

Elro AG40PP User Manual - German - 3 pages

Elro AG40PP User Manual - Dutch - 6 pages

Elro AG40PP User Manual - French - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info