708646

Elro AG400011 - Home Alarm System Manual

5
Zoom out
Zoom in
Previous page
1/6
Next page
4. The system should arm successfully using the new PIN code.
Perform a quick test after the system has been set up and configured.
1. First disarm the system using the app
2. Re-arm the system using the app
3. Trigger an alarm using the PIR and door/window detector.
4. Use the remote control to turn off the alarm once it has been triggered.
5. Check the notifications to ensure that they are correct.
Note: To conserve its battery life, the PIR Motion sensor can be triggered only once every 2
minutes.
Daily operations from alarm panel:
Function Button Icon Remark Action
Arm
Activates the alarm for monitoring. Enter (PIN code) +
Disarm
Deactivates the alarm.
Enter (PIN code ) +
Alarm Panel
Selecting a suitable location:
Mount the alarm panel close to the door which you normally use to enter/exit your house.
Note that the alarm panel requires a power outlet to function properly.
Ensure the location selected has good GSM
reception. You can do this by cross checking the
signal bar on your phone at that location.
The panel must not be located or operated in
conjunction with any other nearby transmitter or
antenna.
1. Remove the back panel mounting bracket of the alarm panel and mount the bracket on the
wall using wall anchors and screws.
2. Once secured, ensure the power is connected and reattach the alarm panel to the secured
mounting bracket.
Door/Window contact
If possible, locate sensors within 100 ft. (30m) of the panel. While a transmitter may have a range
of 350 ft. (106 m) or more out in the open, the environment at the installation site can have a
significant effect on transmitter range
1. Mount the sensor on the door frame and the
magnet on the door. If the sensor is used on
double doors, mount the sensor on the least-
used door and the magnet on the most-used
door.
2. Place sensors at least (1.5 m) above the floor to
ensure the best transmission range.
3. Make sure the alignment arrow on the magnet
points to the alignment mark on the sensor.
4. Avoid mounting sensors in areas where they
will be exposed to moisture or high
temperatures.
5. Use spacers (not included) to keep sensors and
magnets away from metal or metallic surfaces
such as foil wallpaper.
PIR Motion Sensor
The recommended position for a PIR Detector is in the corner of a room mounted at a height
between 1.8 and 2m. At this height, the detector will have a range of up to 10m with a field of view
of 110° (see figure below).
Keep sensors within 30 m (100 ft) of the alarm panel.
Step 13 – Final test before mounting the system
Step 14 – Mounting the system
9
1
3
5
7
Corner mounted
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro AG400011 - Home Alarm System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro AG400011 - Home Alarm System in the language / languages: English as an attachment in your email.

The manual is 1,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro AG400011 - Home Alarm System

Elro AG400011 - Home Alarm System User Manual - English - 15 pages

Elro AG400011 - Home Alarm System Quick start guide - German - 5 pages

Elro AG400011 - Home Alarm System User Manual - German - 12 pages

Elro AG400011 - Home Alarm System Quick start guide - Dutch - 5 pages

Elro AG400011 - Home Alarm System User Manual - Dutch - 236 pages

Elro AG400011 - Home Alarm System Quick start guide - French - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info