471126

Elica Artica AST Manual

4
Zoom out
Zoom in
Previous page
1/7
Next page
Consult the designs in the front pages referenced in the text
by alphabet letters. Closely follow the instructions set
out in this manual. All responsibility, for any eventual
inconveniences, damages or fires caused by not complying
with the instructions in this manual, is declined.
The cooker hood must be placed at a minimum distance of
50 cm from the cooking plane for electric cookers and 75cm
for gas or mixed cookers.
The hood can be installed above these heights but for
optimum performance it should be installed at the distance
quoted for the appropriate heat source.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only.
The hood is equipped with a top air outlet B for discharge
of fumes to the outside (Ducting version exhaust pipe
and pipe fixing clamps not provided).
Should it not be possible to discharge cooking fumes and
vapour to the outside, the hood can be used in the filter
version, fitting an activated carbon filter and the deflector F
on the support (bracket) G, fumes and vapours are recycled
through the top grille H by means of an exhaust pipe
connected to the top air outlet B and the connection ring
mounted on the deflector F (exhaust pipe and pipe fixing
clamps not provided).
The models with no suction motor only operate in ducting
mode, and must be connected to an external suction device
(not supplied).
Expansion wall plugs are provided to secure the hood to
most types of walls/ceilings. However, a qualified technician
must verify suitability of the materials in accordance with the
type of wall/ceiling. The wall/ceiling must be strong enough
to take the weight of the hood.
Do not tile, grout or silicone this appliance to the wall.
Surface mounting only.
Installation - Fig. 5
Preliminary information for installation of the hood
Assembling the chimney flue support/bracket (3
parts):
The three parts should be fixed with 4 screws, the support
extension is adjustable and should correspond to the internal
width of the telescopic chimney flue.
Disconnect the hood during electrical connection, by turning
the home mains switch off.
Remove the 2 screws fitted inside the lower part of the
hood at the points in which it is fixed to the suction unit (see
also operation 3 - remove the grease filter/s).
1. Rest the suction unit on a flat surface and thread the lower
part of the hood onto it.
2. Connect the sensor to the small plate on the front of the
suction group (A  the male and female connectors have
an obligatory access) and the lamps (C).
Connect the control panel to the small plate located on
the front of the suction group (B  the male and female
connectors have an obligatory access).
3. Fasten the hood to the suction unit using 8 screws.
4. Using a pencil, draw a line on the wall, extending up to
the ceiling, to mark the centre. This will facilitate
installation.
5. Rest the drilling template against the wall: the vertical
centre line printed on the drilling template must correspond
to the centre line drawn on the wall, and the bottom edge
of the drilling template must correspond to the bottom
edge of the hood: bear in mind that, when installation is
complete, the underside of the hood must be at least 50
cm above the cooker top in the case of electric cookers,
and at least 75 cm above the cooker top in the case of
gas or mixed cookers.
6. Rest the support bracket on the drilling template so that
it coincides with the dotted rectangle, mark the two outer
holes and drill them, remove the drilling template, insert
2 wall plugs and fix the hood support bracket into place
using two 5x45mm screws.
7. Hang the hood on the bracket.
8. Adjust the distance of the hood from the wall.
9. Adjust the horizontal position of the hood.
10.From inside the suction unit, use a pencil to mark the hole
to be used for final fixing of the hood.
11.Remove the hood from the bracket.
12.Drill at the point marked (Ø8mm - see operation 10).
13.Insert 1 wall plug
14.Rest the chimney support bracket G against the wall,
touching the ceiling. Use the support bracket as a drilling
template (the small slot formed on the support must
coincide with the line drawn on the wall as above
operation 4) and mark 2 holes with a pencil, drill the holes
(Ø8mm), insert 2 wall plugs.
15.Fix the chimney support bracket to the wall using two
5x45mm screws.
16.Hook the hood onto the bottom bracket.
17.Fix the hood into its final position on the wall using one
5x45mm screw (ABSOLUTELY ESSENTIAL).
18.Connect a pipe (pipe and pipe clamps not provided, to
be purchased separately) for discharge of fumes to the
connection ring located over the suction motor unit.
If the hood is to be used in ducting version, the other end
of the pipe must be connected to a device expelling the
fumes to the outside. If the hood is to be used in filter
version, fix deflector F to the chimney support bracket
G using 4 screws, and connect the other end of the pipe
to the connection ring on deflector F.
19.Make the electrical connections.
20.Apply the chimney stacks and fasten them at the top to
the chimney support G (20b) using 2 screws (20a).
INSTRUCTION ON MOUNTING AND USE GB
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elica Artica AST at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elica Artica AST in the language / languages: English as an attachment in your email.

The manual is 0,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info