Manual Elektrobock PT 32 GST (page 6 of 10) (English)

600925

Zoom out

Zoom in

1/10

HYSTERESIS

MIN TIME ON

PI ZONE

PRE SWITCH MOdE

SUMMER MOdE

Odd-EVEN MOdE

HEATING

TEMP CORRECT

(factory setting of 2 min.)

MINIMUM SWITCH-ON TIME

(factory setting of 2 °C)

PI-CONTROL BAND

Set the interval by turning the “ “ button, and conﬁ rm with the “ “ button.

Select within the range of 1 to 5 minutes. The setting is given by the

heating system type, and depends on the PI-control time period selection.

Setting according to the table is recommended.

Set the value by turning the “ “ button, and conﬁ rm with the “ “ button.

TThis value determines the temperature at which the PI-control starts functioning. For example, the

desired temperature is 22 °C, the proportional band is 1.5 °C. Up to 20.5 °C, the source heats fully.

When this value is reached, the PI-control starts. The PROPORTIONAL band can be set within the

range of 0.5 to 3.0 °C (by 0.1 °C).

Set the PI band by turning the “ “ button, and conﬁ rm with the “ “ button.

SETTING HYSTERESIS PARAMETERS

(factory setting of 0.5 °C)

(factory setting of 2 min)

HYSTERESIS

MINIMUM SWITCH-ON TIME

SETTING PI-CONTROL PARAMETERS

(factory setting of 10 min.)

PI-CONTROL INTERVAL

Select according to the object’s thermal inertia. The optimum setting usually falls within the range of

10 to 15 min. The adjustable range is 5 min to 20 min (by 1 min).

Here you can set the minimum switch-on time of the boiler in minutes at hysteresis. Select within the

range from 1 to 5 minutes according to the type of the heating system used (see the table).

Set from 0.1 to 6 °C. According to the value preset, the thermostat switches on at the temperature:

T switching = T required - HYSTERESIS

Set the hysteresis by turning the “

“ button, and conﬁ rm with the “ “ button.

Set the value by turning the “

“ button, and conﬁ rm with the “ “ button.

Heating type

Minimum source

switch-on time

Electric heating

Plate radiators

2 (3)

Cast iron radiators

Floor heating

This function guarantees you the required temperature at the required time. You need not consider when

to switch the heating on in order to be warm when getting up in the morning without heating unnecessarily

long in advance. You just program the time at which you want the desired temperature. Within two opera-

ting days, the program ascertains the thermal constants of the room and then it switches the heating on

in advance sufﬁ ciently. The preliminary switch-on time is limited to 2 hours.

PRELIMINARY SWITCH-ON OF HEATING

Set YES/NO by turning the “ “ button and press the “ “ button to conﬁ rm.

(NO set by default)

In this mode, you are not allowed to switch the heating on. It can particularly be used in the summer

period, when you need not heat. After you enable this mode, the “ “ symbol appears on the display.

Note: The anti-freeze protection (3 °C) is still enabled. In this mode, you cannot change the temperature

or set the holiday mode!

SUMMER MODE

Set YES/NO by turning the “ “ button and press the “ “ button to conﬁ rm.

(NO set by default)

If you choose “YES”, the PrU and PrL programs will alternate automatically according to the current week

(even/odd). This setting is suitable, for example, for shift operation (the requirements on thermal comfort

in the object change every week).

EVEN-ODD WEEK SELECTION

(NO set by default)

Set YES/NO by turning the “ “ button and press the “ “ button to conﬁ rm.

Setting the thermostat function.

HEATING = the output relay (for heating systems) switches if the current temperature drops below the desired value

COOLING = the output relay (for cooling systems) switches if the current temperature rises above the desired value

HEATING / COOLING SELECTION

(HEAT set by default)

Set HEAT/COOL by turning the “ “ button and press the “ “ button to conﬁ rm.

This is used for correcting the temperature measured by the thermostat. The setting can only be done

after 12 hours of operation, when the internal sensor temperature has settled. Measure the room

temperature with a thermometer; if it is different from the temperature on the thermostat,

set the correction within the range of -5 °C do +5 °C.

TEMPERATURE CORRECTION

Set the correction by turning the “ “ button and press the “ “ button to conﬁ rm.

(0 °C set by default)

My device has worked well for many years. Recently changed the SIM card and i keep getting SMS Disconnected as a message.....what could be the solution to resolve please? Submitted on 23-11-2020 at 14:55
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elektrobock PT 32 GST in the language / languages: English as an attachment in your email.

The manual is 3,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elektrobock PT 32 GST

Elektrobock PT 32 GST User Manual - German - 10 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elektrobock PT 32 GST Manual

Product: