495427

Eks Microsense Infrared Thermometer 8009 Manual

3
Zoom out
Zoom in
Previous page
1/30
Next page
3
Specications
1. Temperature measurement range: 34-42.2°C (93.2~108°F)
2. Operating temperature range: 10~40°C (50~104°F)
3. Storage temperature range: -20~50°C (-4~122°F), RH≤85%
Transportation temperature should be less than 70°C, RH≤95%
4. Compliance with ASTM E1965-98, EN12470-5:2003 Clinical thermometers -
Part 5:Performance of infra-red ear thermometers (with maximum device),
IEC/EN60601-1-2(EMC), IEC/EN60601-1(Safety) standards.
5. This mode converts the ear temperature to display its “oral equivalent.” (according to the
result of the clinical evaluation)
6. °C / °F switch function
7. Battery: one lithium battery CR2032
8. Auto power shut-off
9. Accuracy:+/-0.2°C (0.4°F), 35.5~42°C (95.9~107.6°F); +/-0.3°C (0.5°F) for other range.
Using the thermometer
1. Gently squeeze the sides of the probe cap and twist to
remove. Do not use force in removing the cap.
2. Always use a new and undamaged probe cover.
Attach the probe cover to the connection ring. Fig.1
Important: Place the smooth side (not the adhesive
Caution! Read the instructions before use!
Warning: Proper installation of the probe cover ensures accurate
measurements. If the probe cover has not been connected rmly,
the probe cover icon
will ash on the display. In this case
please check the setting of the probe cover again.
Warning: Keep the probe covers and connection ring away from
children.
3. Make sure the ear passage is clean.
4. Press the ON/MEM button. The thermometer is ready
for use after the ear icon stops ashing and two beeps sound.
5. Gently pull the ear back and up to straighten the ear passage. Fig. 3
To obtain the most accurate reading snugly position the
probe in the ear so that the probe point is in line with the
membrane of the eardrum. Fig. 4
6. With the index nger press the SCAN button until you hear a
beep. Fig. 5
7. The device will shut o automatically if not used for more than 1
minute. This saves battery life.
• Place the center of the probe cover over the end of the probe.
• Insert and push the connection ring until the probe cover
clicks into place. The “click” means that the probe cover has
been connected rmly. Fig. 2
Fig.1
Fig. 2
Fig. 3
Fig. 4
Fever alarm:
If the thermometer detects a body temperature of more than
37.5°C when measuring by the ear or forehead, there will be a
long beep sound followed by three short beep sounds which
warn of potential fever.
Memory - MEM
If the temperature reading is within the normal range of 34 °C to
42.2 °C (93.2 °F to 108.0 °F) when the thermometer is turned o,
the last measurement is saved in the memory.
To recall the previous temperature press the ON/MEN button
once again.
Fig. 5
2
3
4
GB
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eks Microsense Infrared Thermometer 8009 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eks Microsense Infrared Thermometer 8009 in the language / languages: English, German, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 6,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info