644155
38
Zoom out
Zoom in
Previous page
1/42
Next page
76
Error message
Error message Possible cause Solution
CN001: Tilt sensor Maximum gradient exceeded
Excessively steep slope
Exclude the excessively steep slope from the cutting
area
Robot has been picked up Place the robot on a level surface and reset the error.
CN002: Lift sensor The housing has been displaced in an
upward direction because it has been
lifted or because the mower has run
over an object.
Remove the foreign object.
CN005: Bumper deflected The robot has collided with an
obstacle and is unable to move clear
(collision near the base station).
Remove the obstacle
CN007: No loop signal
CN017: Cal: signal weak
No circuit signal.
Error during calibration, circuit signal
too weak.
Check base station power supply.
Check circuit.
Disconnect and then reconnect the transformer.
CN008: Loop signal weak Circuit signal is weak. Check base station power supply.
Check boundary circuit: the cable may be buried too
deep.
Disconnect and then reconnect the transformer.
CN010: Bad position The robot has moved outside the
operating area.
Return the robot to the operating area.
Boundary cable crossover
CN011: Escaped robot The robot has moved outside the
operating area.
Check laying of the boundary cable (curves, obstacles,
etc.).
CN012: Cal: no loop
CN015: Cal: outside
Error during calibration: the robot has
not detected the circuit.
Position the robot at right angles with respect to the
boundary cable; the robot must be able to straddle
the boundary cable.
Check base station power supply.
Check circuit.
Disconnect and then reconnect the transformer.
Boundary cable crossover.
CN018: Cal: Impact Error during calibration, impact Remove the obstacle.
CN038: Battery Battery discharged. Check that there are no obstacles preventing the
robot from docking at the base station.
Check the electrical charging contacts of the base
station.
Circuit is too long or has too many islands.
The robot lawnmower has become stuck.
Defective boundary cable, the
robot is unable to find the base
station.
Check the boundary cable for possible breaks, if
necessary have the circuit tested by an authorized
service centre
Spent battery. The battery has reached the end of its working life.
Contact an
authorized service centre to fit a new battery
Charging circuit electronics faulty. Contact an authorized service centre to replace the
charging circuit board
Robot does not connect with the
charging
contacts.
Return the robot to the base station and ensure the
charging contacts are connected.
Have the charging contacts checked and, if necessary,
replaced by an authorized service centre
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Efco Sirius 700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Efco Sirius 700 in the language / languages: English as an attachment in your email.

The manual is 4,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Efco Sirius 700

Efco Sirius 700 User Manual - German - 42 pages

Efco Sirius 700 User Manual - Dutch - 42 pages

Efco Sirius 700 User Manual - French - 42 pages

Efco Sirius 700 User Manual - Italian - 42 pages

Efco Sirius 700 User Manual - Spanish - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info