663877

EdgeCraft ScissorPro 500 Manual

4
Zoom out
Zoom in
Previous page
1/8
Next page
IMPORTANT INFORMATION
1. WARNING: EVEN THOUGH ALL SCISSORS MAY APPEAR TO BE SIMILAR, THERE ARE
MAJOR DIFFERENCES AMONG THEM THAT MUST BE UNDERSTOOD BEFORE YOU USE THIS
SHARPENER. THE ScissorPro
®
WILL SHARPEN MOST, BUT NOT ALL TYPES OF SCISSORS.
DO NOT ATTEMPT TO SHARPEN HAIR STYLING SCISSORS, PINKING SHEARS, MANICURE
SCISSORS, SERRATED BLADES, TIN SNIPS, SCISSORS GREATER THAN 12” IN LENGTH OR ANY
BLADE THAT DOES NOT FIT READILY IN THE SHARPENING POSITION.
ScissorPro
®
will sharpen most other blades, including those of knife-edge scissors, as
described later. It is essential that you follow the instructions to optimize your results.
2. Obviously, all scissors have two blades, Not so obvious is that often these blades are very
different. When you cut with scissors, one blade (the anvil blade) is below the material, and the
other blade (the cutter blade) is above the material, as shown in Figure 4. With certain scissors,
the blade on top of the material (the cutter blade) does most of the cutting.
There are several ways to distinguish the cutter and anvil blades. Referring to Figures 3 and
4, note the cutter blade usually has the oblong finger-hold and a more rounded tip. The anvil
blade has a more pointed tip and a round finger hold.
3. It is important to be able to identify the special knife-edge type scissors. They have a cutter
blade factory sharpened at a very low angle to form a knife like edge that is extremely sharp.
THE KNIFE-EDGE BLADE MUST BE SHARPENED ONLY WITH THE KNIFE-EDGE ACCESSORY
SUPPLIED WITH EACH ScissorPro
®
. With these scissors, the knife-edge cutter blade does
virtually all the cutting. When sharpening this type of scissors, only the knife-edge cutter blade
needs to be sharpened. If you have any doubt about whether you have this type of scissors,
ask your nearest fabric or sewing center to help you identify these special blades before you
sharpen them.
4
Figure 5. Carefully feel for a burr along the
entire back of the blade. Note arrow for
direction of finger movement when in contact
with blade.
Figure 4. Typical position of the Cutter Blade
and Anvil Blade.
Cutter Blade
Anvil Blade
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft ScissorPro 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft ScissorPro 500 in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info