611868
21
Zoom out
Zoom in
Previous page
1/24
Next page
Transmitter - Micro Remote Control Module Ref : EMML
July 2009 page 21 EMML
PROGRAMMAZIONE
Per effettuare una nuova installazione del Micro Trasmettitore, diversa
da quella precedente, o per eliminare le interferenze prodotte da un
sistema prossimale, è necessario programmare un codice diverso.
L’indirizzo di programmazione si compone di un ”HOUSE” code (da A a P) e di
uno “UNIT” code (da 1 a 16). All’uscita dalla fabbrica, l’indirizzo della coppia
trasmettitore/ricevitore è impostato su A1; procedere come di seguito per impostare
un codice diverso.
A. Accedere alla modalità programmazione.
- Premere brevemente e simultaneamente i tasti START (1) e STOP (0) del Micro
Trasmettitore. Il LED diventa GIALLO.
Quindi il LED lampeggia una volta ROSSO (per l’HOUSE CODE), e una volta VERDE
(per lo UNIT code). Il Micro Trasmettitore è impostato su A-1.
Si hanno a disposizione 6 secondi per programmare un nuovo codice.
B. Impostazione dell’HOUSE CODE.
- Premere e rilasciare il tasto (1) un numero di volte tale da impostare l’HOUSE
CODE desiderato. Esempio: A = Premere una volta, B = Premere due volte, C =
Premere tre volte, ... P = Premere 16 volte.
- Dopo aver impostato l’HOUSE CODE, il LED lampeggerà tre volte GIALLO
per confermare la memorizzazione del codice e luscita dalla modalità
programmazione.
C. Impostazione dello UNIT CODE.
- Ripetere solamente il passo A.
- Premere e rilasciare il tasto (0) un numero di volte tale da impostare lo UNIT
CODE desiderato. Esempio: 1 = Premere una volta, 2 = Premere due volte, 3 =
Premere 3 volte... 16 = Premere 16 volte.
- Dopo aver impostato lo UNIT code, il LED lampeggerà tre volte GIALLO.
VERIFICA
Vericare che il Micro Trasmettitore sia riconosciuto dei ricevitori.
Vericare la funzionalità dell’interruttore On/Off.
È necessario attendere circa un secondo tra ogni comando On / Off.
Durante il cambio batterie, il codice registrato sarà mantenuto dal Micro
Trasmettitore.
Diagnostica guasti - controllare le domande pfrequenti (FAQ) e il
supporto tecnico su www.ebodeelectronics.eu
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ebode EMML at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ebode EMML in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info