515345
3
Zoom out
Zoom in
Previous page
1/32
Next page
3
1. INTRODUCTION
EasyAlarm
®
is an easy to use and reliable auto-dialler including announcement unit that can be used in many ways. The
most important functions are listed below. Please read the instruction manual carefully before you start installation.
Especially pay attention to the safety notes.
EasyAlarm is a reliable monitor
Cause of alarm Notes
Noise* Sensitivity I / II / III (LOW / MED / HIGH)
Keystroke Check call / emergency call
Wired sensor input 1*+ Potential separated sensor contact (NO/NC configurable)
=> possibility to trigger an alarm, if an expected repeated action fails
Wired sensor input 2*+ Potential separated sensor contact (NO/NC configurable)
Wired sensor input 3* Potential separated sensor contact (NO/NC configurable)
Technical states / condition
Failure of main supply
Battery condition
*Alarm delay selectable
+ individual announcement or a single stroke bell can be activated
EasyAlarm calls automatically
Destination Notes
Telephone / mobile phone Connection states Listing in: changeover to hands free on demand
Alarm with hands free connection
Pager Numeric alarm message
Alarm centre With protocol Point ID/Contact ID
Alarms up to nine pre programmed phone numbers
EasyAlarm indicates
Indication Notes
Individual announcement Up to 12 seconds duration, at the beginning of connection
Cause of alarm Cause of alarm (periodical announcement)
State of sensor
Technical state / condition Battery condition
EasyAlarm puts you in contact
Mode of contact Notes
Listening in During connection you can listen into the monitored room
Speaking You can talk to a person any time by changing to hands free mode
EasyAlarm provides security
Security steps Notes
Alarm acknowledgement Without acknowledgement you can program up to nine alarm repetitions
Alarm forwarding Without acknowledgement an alarm will be forwarded to next programmed
number
Check call Remote access with PIN code (4 to 7 digits) at any time
EasyAlarm is a telecontrol system
Actions / Reactions Notes
Activation / deactivation of sensors Wired alarm-sensors can be activated or deactivated at any time during
connection mode
Automatic activation of output By triggering of an alarm an output (i.e. siren) can be switched on
automatically, or during connection mode using tone-dialling command
Remote activation of output In connection mode (tone-dialling command) the output can be switched to
drive for example a heater or air-condition unit
Remote programming: alarm number
and alarm-sequence
Alarm number and alarm-sequence can be changed during connection mode,
using tone-dialling commands
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EasyAlarm CONTROL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EasyAlarm CONTROL in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of EasyAlarm CONTROL

EasyAlarm CONTROL User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info