494554
37
Zoom out
Zoom in
Previous page
1/127
Next page
English - 36 -
Installing the Batteries to the Remote
1. Lift the cover on the back of the remote upward
gently.
2. Install two AAA batteries. Make sure to match the +
and - ends of the batteries in the battery compartment
(observe the correct polarity.
3. Replace the cover.
Connect Power & Antenna/Cable
IMPORTANT: The TV set is designed to operate on 12
V DC. For this, an adaptor is used which gives 12 V
voltage. Connect this adaptor to a system that supplies
110-240V AC, 50/60Hz. After unpacking, allow the TV
set to reach the ambient room temperature before you
connect the set to the mains.
VGA
SPDIF
Coax.OUT
12V
DC IN
Aerial or Cable
VGA
SPDIF
Coax.OUT
12V
DC IN
Switching On/Off
Switching the TV On
Connect the power cord to the 110-240V AC,
50/60Hz.
To switch the TV on from standby mode:
Press the
button and the TV will switch to
standby mode. Then the standby LED lights up.
To switch on the TV from standby mode either:
a. Press the
button, CH ^ / v or a numeric button
on the remote control.
b. Press the middle of the “
” button on the TV.
By either method the TV will switch on.
Switching the TV Off
Press the “ button on the remote control or press
the standby
button, so the TV will switch to
standby mode.
To turn off the TV completely, remove the power
cord plug from the mains power socket.
Note: When the TV is switched to standby mode, standby LED
can blink to indicate that features such as Standby Search, Over
Air Download or Timer is active. The LED can also blink when
you switch on the TV from standby mode.
First Time Installation
When turned on for the rst time, the language
selection” menu appears. The message Welcome
please select your language! is displayed in all
language options listed alphabetically.
Press the or button to highlight the
required language, press OK button to select. “First
Time Installation” appears. Use “
” or “ ” button to
set the required country, and press button to
select Search Type (optional).
Use
or to set the desired search type. Available
search types are Digital and analog, digital only and
analog only.
When set, press
to select Teletext Language.
Use
or to select the desired Teletext Language.
Next, select Scan Encrypted and set as Yes if you
want to scan coded stations.
To POWER
INPUT DC 12 V
terminal
AC adapter
37

Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dual 19911 LED at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dual 19911 LED in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 30,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info