653293

Drayton Digistat plus 30002 - RF601 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
Remove battery
compartment
clearance
To tamper proof the product i.e. prevent unauthorised adjustment of
value.
1. Internal temperature sensor has failed.
2. Ambient temperature is outside product operating temperature range.
E I
life remaining) the battery symbol will flash in the display, it is
recommended to change the batteries during this period.
Remove the battery compartment by pinching the tabs and
withdrawing downwards. Replace the spent batteries with 2 x AA 1.5V
alkaline batteries ensuring correct orientation. Replace the battery
compartment pressing fully home.
The green LED will be on when there is a demand for heating, and
off when there is no demand.
The red LED will flash for 7 seconds, approximately every 5
minutes. This denotes that a radio signal is being received from
the Digistat+RF unit.
Situations Requiring Attention
approaching the end of their life (see ‘battery replacement’).
signal from the Digistat+RF unit. This may be caused by the
batteries being dead (see ‘battery replacement’) or some
temporary interference with the radio signal.
the battery drawer, after a few seconds (the display will go blank)
close the battery drawer and then reset to your desired
temperature. If the radio signal has been successfully transmitted
and received, the red LED will flash for 7 seconds then go off.
require the attention of a heating engineer/electrician.
the red LED will stay on until a satisfactory signal is reinstated.
automatically reset itself for normal operation.
Combi boiler basic wiring layout
Zone control basic wiring layout
Standard for all models
If more than one ‘wireless system’ is fitted within the same property.
1. Install (see installation instructions) and turn power on to the
switched on. The red LED should come on.
also come on. Check to see if the boiler and/or motorised valve
are working.
3. To enter ‘learn’ mode push the button marked 1 followed by 2
learn mode. Release both buttons.
4. The red and green LED’s should both now be on.
than one metre).
6. Insert the batteries into the holder and slide them into the Digistat
RF until the drawer clicks into place.
7. The Digistat RF should now display the actual room temperature.
If the unit has been stored in a cold place, it may take time to
warm up.
8. As soon as the battery compartment is slid back into place, the
The green LED may be on or off depending on the room
temperature at the time of commissioning.
9. If the red LED remains on, slide down the battery drawer on the
Digistat RF, check the battery positions are correct, and once the
display has faded, repeat steps 6 to 8.
dial clockwise until a flame symbol appears, in the left hand
segment of the display.
that the radio signal is being sent and received. After 7 seconds
the red LED should go out and the green one come on.
12. Check to confirm that the boiler and/or motorised valves are
working.
dial anticlockwise until the flame symbol disappears.
seconds both the red and green LEDs should go out. Check that
the boiler and/or motorised valve have powered down.
confirmed the system operates correctly, fit and secure the
Digistat RF to the wall (see installation instructions).
seconds each time a radio signal is received from the Digistat RF. This
will occur approximately every 5 minutes.
replacement Digistat RF or SCR is fitted.
must arrange for a competent electrician to install it for you. Wiring
must conform to the current IEE regulations.
is switched off.
Installation Instructions
Read all installation and commissioning instructions before
proceeding.
Do not switch on until ready to commission.
The system wiring must be able to be fully disconnected from the
mains supply by a switch incorporated in the fixed wiring having a
contact separation of at least 3mm on both poles. Fused at 3A.
position, close to the combi boiler or central heating system wiring
where it is surrounded by metal objects or mains voltage cable, as this
may interfere with the radio signal).
For the best performance install in an open space, at least 30cm
distance from any metal objects including wall boxes and boiler
housing.
final location of the Digistat +RF room thermostat and not less than
30cm from the boiler side panel.
Warning: Installing the SCR too close to the metal side panel or
mains cables may interfere with the radio signal.
1. Loosen the securing screws, remove the wallplate, and if surface
wiring is to be used, snap out the cable entry strip on the bottom
edge of the wallplate with a pair of pliers.
2. Fix the wallplate, terminals at the top, either direct onto the flat
wall using wall plugs and no 6 x1” wood screws or on a flush
wallplate clearances are shown.
relevant diagram, to comply with current IEE regulations.
N L 1 2 3 4
50 mm
minimum
clearance
40 mm
minimum
clearance
40 mm
minimum
clearance
70 mm
minimum
SCR wallplate clearances
This product is double insulated and does not require an earth
be wired in to replace hard wired room or programmable thermostats
shown on the system or boiler wiring diagrams. Always check other
manufacturers instructions for compatibility.
To cancel the Preset Mode & return to normal operation
You can either,
1. If you want to return to your previous setpoint (before you entered
be cancelled and the product will return to normal operation and the
display will show the current room temperature as shown,
22
ºc
2. If you want to set a new setpoint, just rotate the dial until your
required setpoint is shown on the display. After a couple of seconds
the display will change to show the current room temperature as
shown,
22
ºc
To change the user adjustable settings
temperature setting) will be displayed and if turned one more click
Changing the Preset Temperature
I5
ºc
SET
menu as described above, then rotate the dial clockwise until ‘HI’
is showing.
H I
30
ºc
H I
Changing the Minimum Temperature Setting
menu as described above, then rotate the dial clockwise until ‘Lo’
Is showing.
5
ºc
While adjusting the settings within the menu, when you reach the
maximum or minimum possible setting the display will flash to
indicate you cannot adjust the product further, e.g. you cannot set
more than 5sec or wait for 1 minute and it will return automatically.
BOILER
30cm Min
Preferred side of boiler
The range may be affected by
composition/density and number of walls
between the Digistat +RF and SCR
Radio Signal Range:
30m Typically
SCR
Electrical
1. Internal temperature sensor has failed.
2. Ambient temperature is outside product operating temperature range.
E I
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Drayton Digistat plus 30002 - RF601 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Drayton Digistat plus 30002 - RF601 in the language / languages: English as an attachment in your email.

The manual is 4,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info