716474
4
Zoom out
Zoom in
Previous page
1/6
Next page
Introduction
Be familiar with the product before using it for the rst time. Please read the follo-
wing operating instructions and the safety instructions carefully. Use the product only
as described and for the specied application areas. Keep these instructions. Hand
over all documents when passing the product on to third parties.
Intended Use
This product is only suitable for the feeding of pets for private use. The product is not
intended for commercial use.
General safety instructions
Damages caused by non-observance of these operating instructions will void the
guarantee claim! No liability is assumed for consequential damages! No liability is
accepted for damage to property or personal injury caused by improper handling or
neglecting the safety instructions!
Control Panel Keys
MODE - switches between clock or feeding time display. Also increases clock
time during clock / feeding time Set mode
SET – enters settings mode. Also conrms the time you enter and advances to
next setting
START NOW – starts the feeding timer immediately
START TOMORROW- starts the feeding timer the next day
REC – records your personal voice message
PLAY – plays back your recorded voice message
ON SWITCH – turns the feeder on / o. For when the feeder will not be used
for an extended period of time. Turning this switch o will RESET all time and
feeding settings
Getting Started
1. Carefully turn the pet feeder upside down. Remove both battery doors by
squeezing the two tabs and gently pulling each door away
2. Keep the ON switch set to OFF
3. Insert four C size alkaline batteries into the battery tray. Do NOT use old or
-cheap- carbon batteries
4. Close the battery doors, rotate the feeder right-side up and switch ON
5. The feeder will cycle one time until “12:00” is on the LCD display
Note: Your pet feeder makes the food available in this sequence:
Tray 1, Tray 2, Tray 3 to Tray 6. When you want only one feeding, you
should ll only Tray 1; for only 2 feedings, ll Trays 1 and 2 and so
on.
Bell
Hours
Minutes
Start
Tomorrow
PM
Setting the Feeding Time
1. After setting the clock time, press the MODE key one time. (1 1) will show on
the display. This is the feeding-time display mode.
2. Now press and hold the SET key for (2 seconds) to enter Feeding time SET
mode. Feeding will start from the rst feeding number & time. The 1st digit
shows the feeding number (Food Tray 1)
3. The hour digit will now blink (2nd and 3rd digit). Press the MODE key to increase
the time, then press the SET key to conrm the time you set
4. After conrming the 1st feeding time, the next feeding number & time will
show on the display. (1st digit will change to the next feeding number, e.g. 2 or
3 or 4 or 5 or 6 and back to 1) To change the feeding time, repeat step-3
5. Repeat step-3 until all 6 feeding times are set. The display will change back to
clock display mode when all 6 feedings have been set
Setting the Feeding Time
1. After setting the clock time, press the MODE key one time. (1 1) will show on
the display. This is the feeding-time display mode.
2. Now press and hold the SET key for (2 seconds) to enter Feeding time SET
mode. Feeding will start from the rst feeding number & time. The 1st digit
shows the feeding number (Food Tray 1)
3. The hour digit will now blink (2nd and 3rd digit). Press the MODE key to increase
the time, then press the SET key to conrm the time you set
4. After conrming the 1st feeding time, the next feeding number & time will
show on the display. (1st digit will change to the next feeding number, e.g. 2 or
3 or 4 or 5 or 6 and back to 1) To change the feeding time, repeat step-3
5. Repeat step-3 until all 6 feeding times are set. The display will change back to
clock display mode when all 6 feedings have been set
Program examples:
1. Feed once a day at 13:00hr (24hrs display) and feed for 6 days
Feed time 1 & 2 & 3 & 4 & 5 & 6 all equal = 13:00hr
2. Feed twice a day at 10:00 and 20:00 and feed for three days
Feed time 1 = 10, feed time 2 = 20, feed time 3 = 10, feed time 4 = 20, feed
time 5 = 10 and the last time 6 = 20
3. Feed three times a day at 6:00am, 12:00 and 18:00 (6:00pm)
Feed time 1 = 06, feed time 2 = 12, feed time 3 = 18 and so on
1
st
digit
2
nd
digit
3
rd
digit
Feeding
Number
Feeding
Time
Review and Start the feeding timer
1. Use the MODE key to cycle through clock and your set feeding times.
2. Press the START NOW key to start the feeding timer immediately. The bowl will
rotate to the pre-set starting position (Tray 6) and your recorded message will
play once. The BELL icon will now be On
3. Or press the START TOMORROW key and the feeding timer will start at
0:00-Midnight. The bowl will rotate to the pre-set starting position (Tray 6) and
your recorded message will play once. The BELL and Zz icon will now be On
Quick Start Guide
50132 Automatic 6 Meal LCD Clock Pet Feeder
Start
Tomorrow
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dobar 50132 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dobar 50132 in the language / languages: English, German as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info