66428
3
Zoom out
Zoom in
Previous page
1/12
Next page
Tools and material needed
Tools:
Flat and Phillips screwdrivers
Wire cutter
Wire stripper
Electric drill with drills
Crimping tool
Digital multimeter or test lamp
Wire brush, scraper or a piece
of an abrasive sheet to remove
paint for a good ground connection
Grease to protect the ground
connection from corrosion
Material:
Speaker wire: minimum
12 AWG = 4 mm
2
for subwoofers
Sheet metal screws for mounting the
amplifier to the amplifier board and the
amplifier board to the car + some extra
for fuse holder, amplifier ground etc.
Electrical insulation tape
½ inch thick plywood or particle board for
the amplifier to be mounted upon.
Amplifier installation kit:
If available,buy an amplifier installation kit. It
contains normally all you need. This is what you
have to buy if you buy the items separately
20- 25 feet = 6- 7.5 meter power cable,
preferably AWG 0 (50 mm
2
) for CAD15 &
4AWG (21mm
2
) for CAD11
1 pc of ANL fuseholder to install close to the
car battery + fuse. CAD11= 150A, CAD15=
200A
20 feet of AWG 15 = 1,5 mm
2
wire for
remote turn on / off cable from radio.
RCA-cable for input from radio.
- 20 feet or 5 meter for trunk installations
-12 feet or 2 – 3 meter for under seat
installations
One ring crimp terminal
for the amplifier ground connection.
Wire ties
Insulating grommet or insulating tube
Routing wires
Stereo
head unit
3
Professional Tip:
If amplifier installation kits are available with diffe-
rent size of power cable, chose the most heavy
power cable to improve sound quality and to allow
more amplifiers to be installed now or later.
If possible buy AWG 0 = 50 mm
2
(or heavier) cable
for best performance of CAD15, or AWG4 (21 mm
2
)
for CAD11.
High current draw
The CAD11 / 15 are mono amplifiers with high power
output. The current draw is also high so you must make
sure that your vehicles power system (battery and
alternator) can provide all the power you need. If you
have a bad battery or alternator in can result in a poor
sound or even worse, a broken battery or alternator.
CAD11, CAD15
3


Need help? Post your question in this forum.

Forumrules
1

Forum

dls-cad-11

Reset search

  • Could someone please tell me what output MOSFET's are used in a DLS CAD11. I have one in for repair but someone removed all of the output MOSFET's. I have tried 31N20 but the amp is getting too hot & going into protection. Submitted on 4-3-2019 at 13:10

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DLS CAD 11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DLS CAD 11 in the language / languages: English as an attachment in your email.

The manual is 0,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info