66428

DLS CAD 11 Manual

2
Zoom out
Zoom in
Previous page
1/12
Next page
CAD11 &15 include
RCA input and output
High level input with auto start
Continuous variable low pass crossover
Continuous variable subsonic crossover
Bass boost feature
Remote bass level control
Phase control cont. variable 0-180 degrees
Bridge mode master / slave selector
Electronic protection circuitry against
short-circuit, DC offset and thermal overload.
Installation
Before you begin the install
Before you begin you need to read the manual, to have
some tools, cables and other material available. There
is one such list of material on the following page.
Amplifier location
Important
Allow air circulation around the amplifier.
2
Disconnect Battery
Before starting the instal-
lation, always disconnect
the negative terminal of
the battery.
The DLS Peformance series of amplifiers have a
compact design that allows great flexibility in
mounting. You can mount it under a seat or in the
trunk.
When you select a location, do remember that the
amplifier generates a lot of heat.
Choose a location where air can circulate freely
around the amplifier. Do not cover the amplifier with
carpets or hide behind trim panels.
Do not mount the amplifier in an inverted or upside
down position.
Check all locations and placements carefully before
making any cuts, drilling any holes or making any
connections.
This is the best direction to
mount the amplifier to get
the best cooling.
CAD11, CAD15
DLS logo on amplifier cooling flange
The DLS logo on top of the amplifier is attached
with two hex. screws. The logo can be removed
and twisted 90 or 180 degrees, and then screwed
back in wanted position. The logo can be mounted
in four different ways to match your installation.
Removal of side flanges
In order to fasten the amplifier to the surface and
connect speaker and power cables, the flanges on
the sides must be removed. This is done by
loosening the hex screws on top of the amplifier.
Use a 3 mm hex key.
Remove these
screws using a 3
mm hex. key for
removal of side
flange. Remount
after fastening the
amplifier and
connection of the
speaker and power
cables.
2 …


Need help? Post your question in this forum.

Forumrules
1

Forum

dls-cad-11

Reset search

  • Could someone please tell me what output MOSFET's are used in a DLS CAD11. I have one in for repair but someone removed all of the output MOSFET's. I have tried 31N20 but the amp is getting too hot & going into protection. Submitted on 4-3-2019 at 13:10

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DLS CAD 11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DLS CAD 11 in the language / languages: English as an attachment in your email.

The manual is 0,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info