615478
6
Zoom out
Zoom in
Previous page
1/62
Next page
ENG 8
ENGLISH
ENG 9
ENGLISH
To power the camera with batteries please follow these steps:
1.Disconnect the power adapter from Baby Unit and from the power
socket.
2.Open the battery door available in the Baby Unit bottom side (see
the picture).
3.Insert 3 x AAA standard batteries by checking that “+” and “-” marks
match the symbols in the batteries compartment.
4.Close the battery door.
Batteries
compartment
Baby Unit - Pairing
The Baby Unit can communicate with the Parent Unit by using a wireless connection based on
2,4 GHz frequency. To skip interferences or detection from other wireless devices it is necessary
to pair the units. This operation is necessary only one time at the rst use or if you want to
change or add other wireless cameras.
To pair the Baby and the Parent Unit please follow these steps:
The pairing phase must be completed in 30 seconds. Because it is a short time,
we suggest to perform the pairing phase by taking Parent and Baby units near
you. When you nish the pairing phase you can install the Baby Unit in the nal
location.
Pan & Tilt function
1.Connect the 5VDC – 1.000 mA power adapter to Parent Unit and t it in a compatible power
outlet.
2.Power ON the Parent Unit.
3.Press or buttons to select the channel (CH:1, CH:2, CH:3 or CH:4).
4.Connect the 5VDC – 1.000 mA power adapter to Baby Unit and t it in a compatible power
outlet.
5.Press and hold pressed the power ON/OFF button for 5 seconds, the power LED will ash.
The pairing phase is started and you have around 30 seconds to nish it.
6.Whit a thin object press the RESET button available in the back side of Parent Unit. It will
detect the Baby Unit and the LCD panel will show the images captured from the camera.
The camera supports two orientations: horizontal (Pan) and vertical (Tilt).
Horizontal rientation (Pan) Vertical orientation (Tilt)
Troubleshooting
This chapter provides some suggestions in order to x some problem during the installation
or the use of the video baby monitor:
Problem description
Solution
The Parent Unit does not Power
ON.
Check if the battery is full charge or not.
Check if the power adapter is connected to Parent Unit correctly.
Check if the power adapter is tted in a compatible power socket
correctly.
If the power LED is light ON check if the VOX function is enabled
(see VOX function chapter) or TV OUT function is enabled (see TV
OUT chapter).
The Baby Unit does not Power ON.
Check if the power adapter is connected to camera correctly
Check if the power adapter is tted in a compatible power socket
correctly.
Check the camera without the power adapter by using 3 x AAA
batteries.
No video or audio signal.
Try to change the number of channel.
Repeat the pairing phase. For more information, please refer to
Installation and Pairing chapter.
It is not possible to complete the
pairing.
The pairing phase takes about 30 seconds. If you do not
complete all steps in this time you need to repeat the phase. We
suggest to perform the pairing phase by taking Parent and Baby
units near you. When you nish the pairing phase you can install
the wireless camera in the nal location. For more details please
refer to Pairing chapter.
When use Talk & Listen function
the volume is low.
Adjust the volume by pressing
or
buttons. For more details
please refer to Volume chapter.
Increase the Baby Unit Volume. For more details please refer to
Main Menu – Baby Unit Volume chapter.
The quality of audio and/or video is
not acceptable.
Please check the strength of the radio signal and try to change
the antenna orientation by moving the Baby Unit.
Perfect signal
Low signal
No signal
Please do not place camera near electromagnetic interferences
source as HiFi speaker, DECT/Cordless Phone and Hi-Voltage
devices.
When camera works in night vision
the IR lights do not light ON.
It is normal because InfraRed light is not visible at human eyes.
On the monitor there are some
lines and the image is not clear.
The camera is powered by batteries and probably the charge level
is low. Please replace the batteries or remove them and connect
the power adapter.
NOTE
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denver SC-17 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denver SC-17 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info