534695

Cubify CubeX Manual

36
Zoom out
Zoom in
Previous page
1/37
Next page
35
PRINTING THE
CALIBRATION FILE
Download the CubeX calibration le from Cubify.com.
Print the CubeX calibration le as you would any other print le.
READING THE
CALIBRATION FILE
The lines on the calibration print are offset by 0.1 mm. The amount of misalignment can
be calculated by
counting the amount Scale 2 or 3 is offset from Scale 1.
• Scale 1 is printed by Print Jet 1. This is the reference print jet. All offsets are relative
to Print Jet 1.
• Scale 2 is printed by Print Jet 2. This error amount is the amount Print Jet 2 needs its
offsets to be adjusted.
• Scale 3 is printed by Print Jet 3. This error amount is the amount Print Jet 3 needs its
offsets to be adjusted.
HOW TO ADJUST THE
OFFSETS
Touch the relative offset to activate it, a plus and a minus will appear at the side of the
screen. Use this plus and minus to adjust the offset.
PRINT JET 2 Y OFFSET Compare the lines on “Y scale 1” and “Y scale 2” to nd the ones that most accurately
line up. Because variation is small, it may be easiest to spot 3 that look like they all line
up. If this is the case, use the middle one as the correct one. Mark this line with a pen for
easier identication.
On “Y scale 2” count from the center line (with the arrow) to the marked line. If you are
counting down, the scale the number is negative. If you are counting up, the scale the
number is positive. Write down the offset.
• In the example shown in Figure 123, the Y offset for extruder 2 is -0.4mm.
PRINT JET 3 Y OFFSET Compare the lines on “Y scale 1” and “Y scale 3” to nd the ones that most accurately
line up. Because variation is small, it may be easiest to spot 3 that look like they all line
up. If this is the case, use the middle one as the correct one. Mark this line with a pen
for easier identication. On “Y scale 3” count from the center line (with the arrow) to
the marked line. If you are counting down, the scale the number is negative. If you are
counting up, the scale the number is positive.Write down the offset.
• In the example shown in Figure 123, the Y offset for extruder 3 is +0.6mm.
PRINT JET 2 X OFFSET Compare the lines on “X scale 1” and “X scale 2” to nd the ones that most accurately
line up. Because variation is small, it may be easiest to spot 3 that look like they all line
up. If this is the case, use the middle one as the correct one. Mark this line with a pen for
easier identication.
On “X scale “2 count from the center line (with the arrow) to the marked line. If you are
counting left, the scale the number is negative. If you are counting right, the scale the
number is positive. Write down the offset.
• In the example shown in Figure 123, the X offset for extruder 2 is +0.9mm.
PRINT JET 3 X OFFSET Compare the lines on “X scale 1” and “X scale 3” to nd the ones that most accurately
line up. Because variation is small, it may be easiest to spot 3 that look like they all line
up. If this is the case, use the middle one as the correct one. Mark this line with a pen for
easier identication.
On “X scale 3” count from the center line (with the arrow) to the marked line. If you are
counting left, the scale the number is negative. If you are counting right, the scale the
number is positive. Write down the offset.
• In the example shown in Figure 123, the X offset for extruder 3 is +1.1mm.
… 36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cubify CubeX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cubify CubeX in the language / languages: English as an attachment in your email.

The manual is 4,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info