498261

Crunch GTO1200 Manual

10
Zoom out
Zoom in
Previous page
1/32
Next page
10
ENG
+
-
blue = speaker - right - positive
-
+
white = speaker - right - negative
orange = speaker - left - negative
yellow = speaker - left - positive
The subsonic filter is suited to filter the lower frequencies out from the audio signal to avoid unwanted
hum noises from the subwoofer. Set the desired crossover frequency of the subsonic filter by using
the controller (SUBSONIC, Fig. 1, 7). Thus to that only the frequencies above the chosen crossover
frequency will be amplified and the subwoofer plays more precised and efficient.
VARIABLE SUBSONIC FILTER
SUBWOOFER CONNECTIONS
- The total loudspeaker impedance must not be lower than 1 ohm.
- Never connect loudspeaker cables with the ground of the chassis or the +12 V supply voltage.
- If the amplifier is operated with a too low impedance or incorrectly used, the entire sound system
may be damaged. This means a warranty void in such cases.
OPERATING ELEMENTS
Turn the input level control (INPUT LEVEL, Fig. 1, 3) on the amplifier to the MIN. position. Turn then
the volume control of the headunit to 80% - 90% of its maximum volume. Now turn slowly the input
level control on the amplifier (INPUT LEVEL, Fig. 1, 3) in a clockwise direction until you hear some
distortion, then turn back slightly until the distortion is not audible anymore.
INPUT SENSITIVITY
The HIGH LEVEL INPUT (Fig. 1, 2) is suitable to connect the amplifier inputs with speaker wires, if
your headunit is not equipped with pre-amplifier RCA outputs. Extend therefore every regarding speaker
cable from your headunit with appropriate speaker cables from your car audio retailer to the mounting
location of the amplifier. Then connect the each matching loudspeaker cable with the cables of the
included HIGH LEVEL INPUT jack like described below.
NOTE: Never use the HIGH LEVEL INPUT and the RCA inputs at the same time. This may damage
the amplifier seriously. The loudspeaker cables of the HIGH LEVEL INPUT must have no contact to the
ground (GND).
HIGH LEVEL INPUT
The amplifier detects a voltage rise (6 Volts) with a so called ”DC Offset” over the connected input
signal on the HIGH LEVEL INPUT (Fig. 1, 2) when the headunit will be switched on. Hence, the amplifier
will also be turned on. As soon as the headunit will be turned off, the amplifier turns also automatically
off. In this case the turn-on connection (REM, Fig. 2, 2) is not needed.
Note: The Auto Turn On function usually works with 90% of all headunits, because they are equipped
with ”High Power”-outputs. Only with a few older and still existing headunits the Auto Turn On function
is not working.
AUTO TURN ON
Set the desired cross-over frequency by using the controller (LPF, Fig. 1, 8). Thus to that only the
frequencies below the chosen cross-over frequency will be amplified and the subwoofer plays more
precised and efficient.
VARIABLE LOWPASS FILTER
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crunch GTO1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crunch GTO1200 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info