635863

Cointra Thermex Blitz IBL Manual

4
Zoom out
Zoom in
Previous page
1/9
Next page
4
RU
In case of EWH arrangement in hard-to-reach places EVN in order to perform maintenance and
warranty service (mezzanine floors, niches, ceiling voids, etc.), installation and dismantling of EWH is
carried out by the user on his own or for his own account.
6.2.
Connection to water mains
Cold water shall be supplied to EWH using pre-filter with water treatment level not less than
200 µm.
Install pressure relief valve at the cold water inlet marked with the blue ring, with 3.5-4 revolution, ensuring junction
tightness with any water sealing material (flax, FUM tape, etc.).
During water heater operation water may leak out of the exhaust outlet pipe of the safety valve (relief of excessive
pressure when heated). It is recommended to connect to the exhaust outlet pipe rubber or silicone tubing of appropriate
diameter to drain moisture.
Connection to water main system shall be in accordance with Figure 2 (option 1 for IBL-O models
and option 2 for models IBL-U) using copper, multilayer or plastic pipes, as well as special flexible
plumbing feed pipes. When mounting EWH excessive efforts are not allowed to avoid damage to the
pipe.
Do not use used flexible feed pipes. Do not operate the EWH without safety valve or
with valve made by other manufacturers.
After having connected EWH open the EWH cold water tap, hot water outlet tap and hot water mixer
faucet to allow outflow of air from EWH. When complete filling EWH water will constantly flow from
tap faucet. Close the hot water tap on faucet mixer.
When connecting EWH in places not provided with water mains it is allowed to supply water to EWH
from auxiliary tank using pumping station, or from the tank placed at a height of not less than 5
meters from the top of EWH.
If pressure in water pipeline exceeds 0.7 MPa, it is required to install pressure reducing valve to reduce
cold water pressure to normal.
6.3.
Connection to power supply
Before connecting water heater to power supply make sure that it is filled with water!
Before connecting water heater to power supply, make sure that its characteristics conform to those
specified for the heater.
Water heater shall be earthed to ensure its safe operation.
Water heater is equipped with a standard power cord with plug.
Power outlet should have grounding contact with earthing wire and be in a place protected from moisture, or
meet requirements for moisture and splashproofness. Plug it and press “POWER” button to turn on the
EWH.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cointra Thermex Blitz IBL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cointra Thermex Blitz IBL in the language / languages: English as an attachment in your email.

The manual is 0,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info