468917

Clifford Concept 50 Manual

23
Zoom out
Zoom in
Previous page
1/23
Next page
EXAMPLE 1: Turn off siren sound number 2:
1. Look for the siren’s sound number 2 location on the Matrix.
2. The location is at the intersection of column 1 and row 2. Note the column and row
numbers.
3. With the ignition on, enter you disarming code on the PlainView valet switch, then hold
the switch in its momentary position until you hear a chirp and see the LED turn on.
4. Select feature column 1 by pressing the switch to its latched position, then back to
center. After a brief pause, you’ll hear 1 chirp to indicate column 1.
5. Press and release the momentary side twice. You’ll hear a total of two chirps to
indicate that you selected the feature in row 2 of that column.
6. After a brief pause, you’ll hear a single chirp to indicate that sound #2 is now off.
7. Turn the ignition off (you’ll hear 3 chirps) and you’re done!
If you wish to turn siren sound 2 back on, simply repeat steps 1–7.
EXAMPLE 2: Turn off siren sound numbers 4 and 6, then turn on QuietChirps:
This time, we will change the settings of three different features. This time, you’ll hear
the appropriate chirp confirmations, but we won’t make note of them in the instructions
below:
1. Enter program mode (step 3 above).
2. Latched, center to select column 1.
3. Four momentaries, (wait for the one-chirp “feature off” confirmation), then 6
momentaries to jump to row number 6.
4. Four latched-center presses to select column 4.
5. One momentary, (wait for the two-chirp “feature on” confirmation), then turn the
ignition off and you’re done.
You just changed the settings of three different features. It’s so easy, you could even do it
while driving. To set all three features back to their factory settings, just repeat steps 1-5.
Adding new remote controls
For other drivers in your family or if you wish to control Concept systems on your other
cars with the same remote control, you can buy additional remote controls from any
Authorized Clifford Dealer (or call our 24-hour Customer Service Department at
800-824-3208) and program them into the system yourself. Each Concept 50 will respond
to as many as four 12-channel remote controls. To add a new remote control to the
system, use the procedures noted in the
User-selectable features
section on pages 19–21.
How to erase the codes of lost or stolen remote controls
If one of your remote controls is ever lost or stolen, you can erase its digital codes from
the system memory to make sure that the missing remote control can never be used to
disarm your system. To do so, use the “Erase all channels” feature (feature column 2,
row 6 on the Matrix of user-selectable features on pages 20–21). This will clear all
remote control codes from the system memory. Then simply program each remaining
and/or replacement remote control as noted in the Adding new remote controls section
above.
© Copyright Clifford Electronics, Inc., 1994 31-070D/C50OM/194
… 23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clifford Concept 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clifford Concept 50 in the language / languages: English as an attachment in your email.

The manual is 0,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info