Manual Clifford Concept 50 (page 21 of 23) (English)

468917

Zoom out

Zoom in

1/23

User-selectable features

Your Concept 50 allows you to set many of its features to your own personal

preferences. Although the system’s programming capabilities are very extensive, we

have made the programming procedures very simple: to make a change, you just flick

the PlainView switch a few times. Once you’ve changed a few settings, you’ll find that

programming Concept 50 is so easy, you can even do it while driving! The system comes

with all of its features pre-programmed as noted by the bold type in the Matrix of

user-selectable features on the following page. To change any of the settings, use the

steps noted below. To restore the feature to its factory setting, just repeat the procedure:

1. Refer to the Matrix of user-selectable features and make note of the column number

and row number of the feature(s) you wish to program.

2. Insert your ignition key and turn it to the “ON” position, or start the engine (skip this

step if the engine is already running).

3. Enter your disarming code, then press and hold the PlainView switch to its

spring-loaded momentary side for about 3 seconds until you hear a siren chirp.

You’ll also notice that the system LED turns on to indicate that the system is in its

programming mode. The system is now in the “Feature Select” position: the top left

cell of the matrix. From this position, you will first select the feature column (from

left to right), then the feature row (from top to bottom).

4. Select the feature column: To select the column you wish, toggle the switch in and

out of the latched position the same number of times as the column number of the

selected feature (NOTE: each latched-to-center motion is counted as one). After a

one-second pause, you will hear the same number of chirps as the column number

you have selected, audibly confirming your selection.

5. Select the feature row: To select the feature’s row, immediately tap and release the

momentary side of the switch the same number of times as the feature’s row number.

You will hear a single chirp confirmation each time you press the momentary side to

help you count.

VERY IMPORTANT:

If there is a

NOTE

number listed in the selected feature of

the matrix, perform the actions listed for that note. Once you have completed the

NOTE instructions, skip step 6 below and go to step 7.

6. After a one-second pause you will hear either one chirp to indicate that the feature

you selected is now turned off, or two chirps to indicate that the feature is now on (on

the siren duration feature, one chirp = 30 seconds, two = 60 seconds).

7. You have now completed the programming of the desired featured. You may select

another feature, or you may exit program mode:

a. To program another feature in that same column, you must repeat step 5 within

the next 3 seconds (if longer than 3 seconds, you will hear three chirps to indicate

that you are now in the “Feature Select” position).

b. To select a different feature column, go to step 4.

c. To exit program mode, turn the ignition off (you’ll hear 3 chirps and the LED will

turn off to indicate exit of program mode). If driving, just wait for 30 seconds and

the system will automatically exit programming mode by itself (indicated by 3

chirps and extinguishing of the LED).

The above may sound complicated, but it really isn’t. There is just a lot of explanation

involved with each step. Briefly, here is all you do: Choose the feature you want to

change, enter program mode, select the feature’s column and row, then turn off the

ignition. That’s it! Try the examples on page 22 to see just how easy it really is.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Clifford Concept 50 in the language / languages: English as an attachment in your email.

The manual is 0,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Clifford Concept 50 Manual

Product: