300954
188
Zoom out
Zoom in
Previous page
1/325
Next page
Configuring Regional Parameters and Supplementary Services
Miscellaneous Parameters
Cisco Small Business SPA300 Series, SPA500 Series, and WIP310 IP Phone Administration Guide 187
7
Outbound Call Codec Selection Codes
Codec call selection codes affect voice quality. For more information about voice
codecs, see the Configuring Voice Codecs. You can choose a
preferred
codec
for a call or
force
a call to use a specific codec:
Prefer
G.711u (*017110)
through
G.729a (*01729)
—Sets the preferred
codec for next outbound call. If the preferred codec is unavailable, the
second, then the third preferred codec is used, if specified.
Force
G.711u (*027110)
through
G.729a (*02729)
—Forces the specified
codec for next outbound call. If the specified codec is unavailable, the
preferred codecs are used in order, if specified.
See Configuring Voice Codecs for more information.
Miscellaneous Parameters
This section describes Dual Tone Multi-Frequency (DTMF) and localization
parameters:
DTMF Parameters
DTMF is used by touch-tone phones to assign a specific frequency (consisting of
two separate tones) to each key so that it can easily be identified by a
microprocessor.
In-Band and Out-of-Band (RFC-2833): IP phones can relay DTMF digits as
out-of-band events to preserve the fidelity of the digits. This can enhance the
reliability of DTMF transmission required by many IVR applications such as dial-up
banking and airline information.
The following parameters can either reduce false detection or get better detection
by the IVR. In general, the default values are recommended for both IVR functions.
DTMF Playback Level
: Local DTMF playback level in decibels per minute, up
to one decimal place. Applicable locally when a user presses a digit or when
the phone receives an out-of-band (OOB) DTMF signal from the network
side. Does not affect DTMF transmission. Defaults to -16.
DTMF Playback Length
: Local DTMF playback duration in milliseconds.
Affects only OOB. Defaults to .1.
Downloaded from www.Manualslib.com manuals search engine
188

Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cisco wip 310 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cisco wip 310 in the language / languages: English as an attachment in your email.

The manual is 2,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info