555410
10
Zoom out
Zoom in
Previous page
1/16
Next page
A
B
1
3
1
2
3
1
4
3
2
2
3
1
1
5
1
2
3
1
3
4
5
3
16
1
4
5
8
6
7
2
9
10
3
9
17
10
Connect Door Arm to Trolley
A. Preferred Installation:
Disconnect Trolley by pulling on the red handle and slide towards door. With door closed connect Straight Door
Arm (5) to Trolley (4) with Bolt (3), secure with Nut (1). Connect Curved DoorArm (2) to Door Bracket with Bolt (3)
Secure with Nut (1).Align Straight and Curved Door Arms with a 2 hole overlap connect with Bolt (3), secure with
Nut (1), If Straight DoorArm (5) is too long, cut the end of the Door Arm.
B. Where extra travel distance is required:
With door closed connect Curved DoorArm (2) to Door Bracket with Bolt (3), secure with Nut (1). Lift Curved Door
Arm (2) to meet Trolley, connect door arm to Trolley with Bolt (3), secure with Nut (1).
Connect Electric Power
To avoid installation difficulties, do not run the garage door opener until instructed to do so.
Plug the opener into electric outlets as specified by local wiring codes. The opener light will turn on when power is
connected and remain on for 2-1/2 minutes.
Attach Limit Switches
NOTE: The limits must be installed as shown. If installed incorrectly the unit will not function properly.
Close garage door by hand. Determine the position of the Close Limit Switch (1) (Long wire) by aligning the center of
trolley and the center of the Limit Switch. The Limit Switches are actuated by a magnet in the Inner Trolley.
Insert bottom tab (5) of Limit Switch (1) into bottom lip of Rail (7). Insert top tab (4) under top lip of Rail (6). Lift limit
assembly against top lip of Rail and tighten screw (8) to secure Close Limit Switch.
Open garage door by hand to the full open position. Pull red handle to open door past Inner Trolley. Determine the
position of the Open Limit Switch (3) (Short Wire) by aligning the center of the Trolley and the center of the Limit Switch.
Insert bottom tab (5) of Limit Switch (1) into bottom lip of rail (7). Insert top tab (4) under top lip of rail (6). Lift limit
assembly against top lip of rail and tighten screw (8) to secure Open Limit Switch.
Insert wires for Limit Switch (9) into top channel of Rail (10). Secure wires with wire clip. the wires must be secured so
they do not interfere with the travel of the Trolley. Activate remote, the opener will operate and reconnect to the door
automatically.
Run opener 2 full travel cycles. If the door reverses in mid travel go to Setting the Force Section. Adjust Limit Switches
as necessary to fully open and close the door without reversing.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chamberlain ML500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chamberlain ML500 in the language / languages: English as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info