522095
3
Zoom out
Zoom in
Previous page
1/4
Next page
Operation Guide 2926
3
The table below describes button operations you can perform during an elapsed
time measurement operation in the elapsed time mode.
To do this:
Stop the elapsed time operation
Resume a stopped elapsed time operation
Display the countdown start time
Stop the elapsed time operation and display the reset time
Start the countdown from the displayed reset time
Do this:
Press D.
Press D again.
While the elapsed time is
stopped, press B.
Press B.
Press D.
Alarms
Yo u can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms can be configured as a
snooze alarm or a one-time alarm, while the other four are
one-time alarms.
Yo u can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
There are five alarm screens numbered 1 through 5.
The hourly time signal screen is indicated by :00.
When you enter the Alarm Mode, the screen you were
viewing when you last exited the mode appears first.
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Alarm number
Alarm time
(Hour : Minutes)
Timekeeping Mode time
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
x2 x3
:00
x1
x5 x4
You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2
through 5 can be used as one-time alarms only.
The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash. This indicates the setting screen.
This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds. In the case of the snooze
alarm, the alarm operation is performed a total of seven times, every five minutes, until
you turn the alarm off or change it to a one-time alarm.
Note
Pressing any button stops the alarm tone operation.
Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the Alarm
1
setting screen
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn Alarms
22
22
2
through
55
55
5
on and off
1. In the Alarm Mode, use D to select a one-time alarm
(alarm number 2 through 5).
2. Press B to toggle the displayed alarm on and off.
Tu rning on a one-time alarm (2 through 5) displays the
alarm on indicator on its screen.
If any alarm is on, the alarm on indicator is shown on
the display in all modes.
Alarm on indicator
To select the operation of Alarm
11
11
1
1. In the Alarm Mode, use D to select Alarm 1.
2. Press B to cycle through the available settings in the sequence shown below.
The applicable alarm on indicator (
or ) is displayed in all modes when an
alarm is turned on.
The snooze alarm on indicator flashes during the 5-minute intervals between
alarms.
Displaying the Alarm 1 setting screen while the snooze alarm is turned on
automatically turns off the snooze alarm (making Alarm 1 a one-time alarm).
Alarm on Snooze alarm on Alarm off
To turn the hourly time signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal.
2. Press B to toggle it on and off.
Tu rning on the Hourly Time Signal displays the hourly
time signal on indicator.
The hourly time signal on indicator is displayed in all
modes.
Hourly time signal
on indicator
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
The display range of the stopwatch is 99 hours, 59
minutes, 59.99 seconds.
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
Seconds
1/100 second
Minutes
Hours
To measure times with the stopwatch
D
Start Stop
Elapsed Time
Re-start Clear
D
Stop
D
D
B
Split Time
D
Start Split
Split release
Clear
B
Stop
B
D
B
Two Finishes
D
Start Split
Stop
Clear
B
Split release
D
B
B
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
(SPL displayed)
Dual Time
The Dual Time Mode lets you keep track of time in a
different time zone.
The seconds count of the Dual Time is synchronized
with the seconds count of the Timekeeping Mode.
To set the Dual Time
1. Press C to enter the Dual Time Mode.
2. Use A, B, and D to set the Dual Time Mode time.
Each press of D (+) and B (–) changes the time
setting in 30-minute increments.
Pressing A sets the Dual Time Mode to the same time
as the Timekeeping Mode.
Timekeeping Mode time
Dual time
(Hour : Minutes Seconds)
Illumination
The display of the watch is illuminated by an LED (light-
emitting diode) and a light guide panel for easy reading in
the dark. The watch’s auto light switch automatically turns
on illumination when you angle the watch towards your
face.
The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
See “Illumination Precautions” for other important
information about using illumination.
To turn on illumination manually
In any mode, press L to illuminate the display for about
one second.
The above operation turns on illumination regardless of
the current auto light switch setting.
Auto light switch
on indicator
About the Auto Light Switch
Tu rning on the auto light switch causes illumination to turn on, whenever you position
your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you at more than 40 degrees causes illumination to turn on.
Wear the watch on the outside of your wist.
Parallel to
ground
More than
40°
Warning!
Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
startle or distract others around you.
When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down D for about two seconds to toggle the auto light
switch on (auto light switch on indicator displayed) and off (auto light switch on
indicator not displayed).
In order to protect against runnning down the battery, the auto light switch will turn
off automatically approximately six hours after you turn it on. Repeat the above
procedure to turn the auto light switch back on if you want.
The auto light switch on indicator is on the display in all modes while the auto light
switch is turned on.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 2926 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 2926 in the language / languages: English as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 2926

Casio 2926 User Manual - German - 5 pages

Casio 2926 User Manual - Dutch - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info