Manual Casio 2926 (page 1 of 4) (English)

522095

Zoom out

Zoom in

1/4

Operation Guide 2926

MO0503-EB

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully and keep it on hand for later reference

when necessary.

Warning!

• The longitude, lunitidal interval, Moon phase indicator, tide graph data, and solar

azimuth data that appear on the display of this watch are not intended for

navigation purposes. Always use proper instruments and resources to obtain data

for navigation purposes.

• This watch is not an instrument for calculating low tide and high tide times. The

tide graph of this watch is intended to provide a reasonable approximation of tidal

movements only.

• When engaging in mountain climbing or other activities in which losing your way

can create a dangerous or life-threatening situation, always be sure to use a

second compass to confirm direction readings.

• CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any

claims by third parties that may arise through the use of this watch.

About This Manual

• Button operations are indicated using the letters shown

in the illustration.

• Each section of this manual provides you with the

information you need to perform operations in each

mode. Further details and technical information can be

found in the “Reference” section.

(Light)

General Guide

• The illustration below shows which buttons you need to press to navigate between

modes.

• In any mode, press L to illuminate the display.

Moon / Tide Data Mode Countdown Timer Mode

Dual Time Mode

Timekeeping Mode

▲

Alarm Mode

▲

Stopwatch Mode

Press C.

▲

Press B.

▲

Bearing Mode

Press C.

▲

Timekeeping

Use the Timekeeping Mode to set and view the current

time and date.

• The tide graph shows tidal movements for the current

date in accordance with the current time as kept in the

Timekeeping Mode.

• The Moon phase indicator shows the current Moon

phase in accordance with the current date as kept in the

Timekeeping Mode.

Important!

• Moon phase, tide graph data, Bearing Mode solar

azimuth data, and Moon/Tide Data Mode data will not

be displayed properly unless the Timekeeping Mode

current date and time settings and Home Site data are

configured correctly. See “Home Site Data” for more

information.

Day of week

Month – Day

Hour : Minutes Seconds

indicator

Tide graph

Moon phase indicator

To set the time and date

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Hour

Seconds

12/24-Hour

Format

Day Month

Year

Minutes

3. When the setting you want to change is flashing, use D and B to change it as

described below.

Year

To change this setting

Seconds

Hour, Minutes, Year,

Month, Day

12/24-Hour Format

Perform this button operation

Press D to reset to 00.

Use D (+) and B (–) to change the setting.

Press D to toggle between 12-hour (12H) and

24-hour (24H) timekeeping.

4. Press A twice to exit the setting screen.

• The first press of A displays the GMT differential setting screen. Pressing A again

exits the setting screen.

• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all modes.

• The day of the week is displayed automatically in accordance with the date (year,

month, and day) settings.

Home Site Data

Tide graph data and Bearing Mode solar azimuth data will not be displayed properly

unless Home Site data (GMT differential, longitude, and lunitidal interval) is configured

correctly.

• The GMT differential is the time difference of the time zone where the site is located

from Greenwich Mean Time.

• Note that you must add one hour to the GMT differential for your time zone

whenever you change to Daylight Saving Time. Subtract one hour when you change

back to Standard Time.

• The lunitidal interval is the time elapsing between the Moon’s transit over a meridian

and the next high tide at that meridian. See “Lunitidal Interval” for more information.

• This watch displays lunitidal intervals in terms of hours and minutes.

• The “Site/Lunitidal Interval Data List” provides GMT differential, longitude, and

lunitidal interval information around the world.

• The following is the initial factory default Home Site data (Tokyo, Japan) when you

first purchase the watch and whenever you have the battery replaced. Change these

settings to match the area where you normally use the watch.

GMT differential (+9.0); Longitude (East 140 degrees); Lunitidal interval (5 hours,

20 minutes)

To configure Home Site data

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press A again to display the GMT differential setting

screen.

3. Press C to move the flashing in the sequence shown

below to select other settings.

Lunitidal Interval

Hours

Lunitidal Interval

Minutes

Longitude

GMT

Differential

4. When the setting you want to change is flashing, use D and B to change it as

described below.

GMT differential

Setting

GMT Differential

Longitude

Lunitidal Interval

Hours, Minutes

Screen Button Operations

Use D (+) and B (–) to change the setting.

• Yo u can specify a value in the range of –11.0

to +14.0, in 0.5-hour units.

Use D (+) and B (–) to change the setting.

• Yo u can specify a value in the range of

179°W to 180°E, in 1-degree units.

Use D (+) and B (–) to change the setting.

5. Press A to exit the setting screen.

Bearing Mode

The Bearing Mode lets you determine approximate

directions using a displayed angle value that indicates the

angle to the sun (solar azimuth).

• All of the operations in this section are performed in the

Bearing Mode, which you can enter from the

Timekeeping Mode by pressing B.

Important!

Before the watch can calculate the solar azimuth (the

angle of the sun in relation to your location) correctly, you

must first set the correct current time, current date, and

Home Site in the Timekeeping Mode. You must also

specify whether the sun traverses the sky to the north or

to the south of your current position.

Solar azimuth

• Note that you cannot use the Bearing Mode to determine directions in the following

cases.

When the sun is not visibl

At night

When sun traverses the sky directly overhead or when you cannot determine if it

traverses to the north or south

To set the traverse direction of the sun

1. In the Bearing Mode, hold down A until N or S flashes

on the display. This indicates the setting screen.

2. Press D to toggle the setting between N (north) and S

(south).

3. Press A to exit the setting screen.

• At this time the watch uses the traverse direction setting

you just configured and the Timekeeping Mode data to

calculate and display the solar azimuth.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Casio 2926 in the language / languages: English as an attachment in your email.

The manual is 0,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 2926

Casio 2926 User Manual - German - 5 pages

Casio 2926 User Manual - Dutch - 5 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Casio 2926 Manual

Product: