469905

Carrera Digital 124 - 23608 Race Competition en WIRELESS Manual

5
Zoom out
Zoom in
Previous page
1/8
Next page
11
Preparation of start
receiver/tower


Please connect the receiver as shown in gure
. When connect-
ing one tower it is irrelevant which speed controller-connector you
choose to connect the receiver/tower. Please take into considera-
tion that the WIRELESS system only works with the signals of the
Wireless speed controller being able to be received by the receiver,
not being interrupted by any objects or persons.
The Carrera DIGITAL 124/132 Black Box allows a mixed operation
of WIRELESS- and wired speed controllers ( up to a maximum of
6 speed controllers).
Switch on Black Box as per gure
. Turn on speed controller on
bottom-side (g.
). Directly after the speed controller has been
switched on the speed controller´s encoding will be indicated by
the number of ashings, see gure
(e.g. ashing 3x = speed
controller 3). After 2 seconds the LED switches to a ashing rhythm
at regular intervals indicating readiness for operation. In case the
speed controller is not activated it automatically switches to the
energy-saving mode after 20 seconds. By pressing the tappet or the
lane-change-button the speed controller can be reactivated.
Encoding Wireless
speed controller
Switch on speed controller while pressing lane-change-button on
speed controller´s bottom (g.

+
). LED lights permanently
(g.
). Release lane-change-button and push accordingly (e.g.
push 2x = speed controller 2)(g.
). Conrm programming by
pressing speed controller´s tappet (g.
). Successful program-
ming will be indicated by LED ashing according to the encoding
(g.
).
Insertion/exchange
of batteries
OFF / ON
To operate the WIRELESS speed controller 3 x AA (R6) batteries
are required (not included in delivery). A reduced range between the
speed controller and the receiver/tower and a minor driving perform-
ance of the vehicles are an indication of a battery power drop. In this
case the batteries need to be exchanged at the bottom of the speed
controllers (g.
) as illustrated (g.
).
Using new batteries/rechargeable batteries a permanent playing
time of approx. 48 hours or a standby time of approx. 200 hours
can be assumed.

Operation with rechargeable batteries is not possible.
Preparation of start
This Carrera DIGITAL 124 vehicle ideally matches the Carrera track
system scale 1:24.
Depending on the car type it is advisable to remove or not to im-
plement the spacing plate when using a Carrera crossing or high
banked curve. With those track elements being used, slight driving
noises may occur. These are caused by the cars´ scale authenticity
and do not have any inuence on a faultless operation.

To ensure proper and continuous driving, slightly fan out the ends
of the contact brushes
and bend them towards the track as per
g.
. Only the end of the contact brush should have contact to the
track and may be cut o slightly in case of wear. Dust and abrasion
should be removed from track material and sliding contacts from
time to time.
Preparation of start and
points function
Make sure that the car’s guide keel is located inside the
track slot and that the double sliding contact is in contact with the
current carrying track.
Place the cars onto the connecting track.
       

Replacement of double
contact brushes and guide keel
In case the car is lifted, the rocker bar folds up slightly (g.
).
For changing the guide keel or the double contact brushes the
rocker bar can be folded up widely according to g.
.
For changing the guide keel and the double contact brushes the
guide keel should be removed rst.
Afterwards both double contact brushes can be removed and
changed. Please take care that in stage one the upper contact
brush
is only pulled out partly and in stage two the double
contact brush is pulled out completely with the contact brush
For inserting please proceed the same way.
Height adjustment
car chassis
Before you can begin adjusting the chassis and the magnets it is
necessary to detach the car body from the vehicle. Remove the
mounting screws on the underside of the car and lift o the car
body.

Remove the two screws from the front axle mounting and detach
the entire front axle including the mounting from the chassis.
Detach the mounting from the axle, turn it through 180 degrees
and insert the axle back into the mounting
. Now you can return
the front axle and mounting unit to the chassis.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carrera Digital 124 - 23608 Race Competition en WIRELESS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carrera Digital 124 - 23608 Race Competition en WIRELESS in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info