536888
4
Zoom out
Zoom in
Previous page
1/17
Next page
RMD 212BT MANUAL
4
Owner’s Manual
and the speakers. Check the condition of your speakers care-
fully- connecting this unit to old or degraded speakers may re-
sult in a fault which will damage the audio IC and invalidate the
warranty.
If this unit is installed in a vehicle that does not have an ACC
(accessory) position on the ignition switch, the red lead of the
unit should be connected to a terminal coupled with ignition
switch ON/Off operations. If this is not done, the vehicle battery
may be drained when you are away from the vehicle for several
hours.
Secure the wiring with cable clamps or adhesive tape. To pro-
tect the wiring, wrap adhesive tape around them where they lie
against metal parts. To avoid short-circuiting, cover all discon-
nected lead with insulating tape. There is a possibility of short-
circuiting if the leads are not insulated.
Route and secure all wiring so it cannot touch any moving
parts, such as the gear lever and handbrake. Do not route wir-
ing in places that get hot, such as near the heater outlet. If the
insulation of the wiring melts or gets torn, there is a danger of
the wiring short-circuiting to the vehicle’s body.
Don’t pass the yellow lead through a hole into the engine com-
partment to connect to the battery. This will damage the lead’s
insulation and cause a very dangerous short.
• Do not shorten any leads. If you do, the protection circuit may
fail to work when it should.
• Never feed power to other equipment by cutting the insulation
of the power supply lead of the unit and tapping into the lead.
The current capacity of the lead will be exceeded, causing over-
heating.
Since a unique audio I/C circuit is employed, never wire so
the speaker leads are directly grounded or the left and right
– speaker leads are common.
When this product’s source is switched ON, a control signal
is outputted through the orange lead. Connect to an external
power amp’s system remote control or the car’s Auto-antenna
relay control terminal (max. 300mA 12 V DC). If the car features
a glass antenna, connect to the antenna booster power supply
terminal.
When an external power amp is being used with this system,
do not connect the orange lead to the amp’s power terminal.
Likewise, do not connect the orange lead to the power termi
nal
of the auto-antenna. Such connection could cause excessive
current
drain and a major malfunction. Refer to the relevant owner’s manual
Warnings Before Installation
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caliber RMD212BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caliber RMD212BT in the language / languages: English as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Caliber RMD212BT

Caliber RMD212BT Quick start guide - English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info