165912
2
Zoom out
Zoom in
Previous page
1/9
Next page
4
ENGLISH
3
ENGLISH
2
RCA INPUT
Connect the RCA-outputs of your radio to the RCA input terminals of the amplifier.Take good care
that you connect the Right output of your radio to a Right input of your amplifier, and that you con-
nect the Left output of your radio to a Left input of your amplifier.
AMPLIFIER ADJUSTMENTS
Put the input level adjustment knob to the minimum.
Put the volume of your radio to 3/4 of the maximum.
•Now adjust the input level. Slowly turn up the input level and listen carefully untill you hear the
amplifier begin to distort. A Caliber Amplifier “clips” very softly, so this can sometimes be a difficult
adjustment.You will hear that the Bass you wanted can be required in this way.
CALIBER WARRANTY
Due to the complexity of our products, we strongly recommend that this amplifier is installed by
your authorized Caliber dealer. If properly installed by your dealer we provide a warranty for 12
month from the date of purchase.
If you install this amplifier yourself, we wish you lots of fun and succes in doing so. If you follow our
guidelines, you’ll get the best result. Our warranty, however, will be limited to and not exceed 30
days from the date of purchase.
FEATURES
•Bridgeable outputs.
Pulse Width Modulated (PWM) MOSFET Power Supply.
Thermal-, Overload- and Shortcircuit protection.
•RCA in- and outputs.
Phase-control 0 - 180º
Adjustable input-level.
•Variable low-pass control 40 - 160Hz.
Excellent muting circuitry assures no turn on/off ‘pops’.
Goldplated power connectors for optimal power distribution.
European design and engineering.
Goldplated speaker connectors for optimal signal output.
MOUNTING
The amplifier should be protected from exposure to moisture and direct sunlight.
Mark the mounting surface using the amplifier as a template, then drill 2.5mm (1/8”) diameter holes
at the marked locations and mount the amplifier using the supplied self-tapping screws.
INSTALLATION
Remember to always disconnect battery ground before working on a vehicle’s electrical system!
Always place a fuse or circuit breaker no more than 30cm (12”) from the battery, no greater than
the fuse(s) of your amplifier for optimal protection.
GETTING YOUR POWER STARTED
First, the +12V terminal is connected directly to the battery of your car. Use a cable of at least 10
mm
2
(8 AWG), and make sure that the connectors are of the same value.
- Don’t forget the extra “Vehicle protection” fuse.
- The 12V + terminal should NOT be connected to the car fuse box.
Second, the ground terminal (GND) must be fastened securely to the chassis of the vehicle with the
same gauge cable as the positive cable (the same amount of power has to run through it). Ensure
that all paint, undercoating or any other insulation is removed from the area where you want to
make your ground connection to.
•Third, the last cable to connect is your remote turn-on (REM). Many radio-cassette and CD-players
have an output terminal for connection of the REM of an amplifier. If you don’t have such an out-
put, a separate switch must be installed to control your amplifiers on/off function.
CA 300BC/Manual 06-01-2003 15:00 Pagina 2
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caliber ca 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caliber ca 300 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info