497400
2
Zoom out
Zoom in
Previous page
1/24
Next page
Bridgeable outputs.
’Tri-mode’ output capability, simultaneous stereo & bridged mono set up is possible.
Pulse Width Modulated (PWM) MOSFET Power Supply.
Variable input sensitivity: RCA input 0.5V to 2V.
Thermal-, Overload- and Shortcircuit protection.
Excellent muting circuitry assures no turn on/off ‘pops’.
Built-in High Pass / Full Range / Low Pass Filter Switch. 50Hz - 250Hz
Chrome plated power connectors for optimal power distribution.
European design and engineering.
Chrome plated speaker connectors for optimal signal output.
The amplifier has to have at least 5 cm (2”) ventilation space at all sides, to allow the heat to rise
away from the amplifier. Be sure that the power and signal cables can enter and leave the ampli-
fier in a straight line, to avoid the risk of malfunction. Always place the power- and signalcables at
opposite sides of the vehicle to reduce any noises.
The amplifier should be protected from exposure to moisture and direct sunlight.
Mark the mounting surface using the amplifier as a template, then drill 2.5 mm (1/8”) diameter
holes at the marked locations and mount the amplifier using the supplied self-tapping screws.
Remember to always disconnect battery ground before working on a vehicle’s electrical system!
Always place a fuse or circuit breaker no more than 30 cm (12”) from the battery, no greater
than the fuse(s) of your amplifier for optimal protection.
   
First, the +12V terminal is connected directly to the battery of your car. Use a cable of at
least 10 mm
2
, and make sure that the connectors are of the same value.
- Don’t forget the extra “Vehicle protection” fuse.
- The 12V + terminal should NOT be connected to the car fuse box.
Second, the ground terminal (GND) must be fastened securely to the chassis of the vehicle with
the same mm
2
cable as the positive cable (the same amount of power has to run through it).
Ensure that all paint, undercoating or any other insulation is removed from the area where you
want to make your ground connection to.
Third, the last cable to connect is your remote turn-on (REM). Many radio-cassette and
CD-players have an output terminal for connection of the REM of an amplifier. If you don’t have
such an output, a separate switch must be installed to control your amplifiers on/off function.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caliber CA 2050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caliber CA 2050 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 2,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info