532522
2
Zoom out
Zoom in
Previous page
1/2
Next page
Door Bell Operation
Press the button on the push button unit once, the LED indicator will light up
during signal transmission for 1 second and the door chime unit will sound.
The sound will stop as soon as the melody ends. For repeat sound, press the
button again. Holding the button in will NOT repeat the sound.
Sound Adjustment
To slightly adjust the sound of the bell, loosen the screw
that holds the dome in place. Turn the dome and then
tighten the screw.
Important
1. Do not mount the Push Button unit onto any metal or
UPVC doorframe as this will reduce the operating
range.
2. Do not immerse either unit in water.
3. Do not expose either unit to high temperatures or
close to fireplace.
4. Do not use different type of batteries, or mix up old
and new batteries.
5. Do not leave exhausted batteries in either unit. If leaving the doorbell for a
long period of time, remove the batteries from all compartments to prevent
leakage.
6. The chime unit is designed for internal use only.
7. Please dispose of old, defective batteries in an environmentally friendly
manner in accordance with the relevant legislation.
8. The unit should not be exposed to or placed near sources of water or direct
heat.
9. Replace batteries only with the same or equivalent type recommended by the
manufacturer.
10. Do not place near a P.I.R. which may interfere with your chime.
3. Select any combination ensuring it is set to the same code on both push
button and door chime units. E.g. If the 1 & 2 dipswitches are down in
your push button, then the 1 & 2 dipswitches must be down in your
chime unit.
4. Test to ensure correct operation before final installation.
Trouble Shooting & User Hints
Problem
Chime does not
sound but LED
lights on Push
Button
Possible Causes
1. Units is out of range (max.
range 100m)
2. Push button and chime not
on same channel
Suggested Remedy
Operate the Chime unit within the
operation range (100m)
Re-set the channel (see Channel
Set Up)
Chime does not
sound plus no
lights on Push
Button LED
1. Flat push button battery
2. Wrong polarity of battery in
push button
3. Remove the protective Strip.
Change the battery
Re-insert battery as internal
marking in right polarity
Chime sounds
without push
button being
pressed
A similar wirfree door chime
product is operating nearby
on the same transmitter
frequency
Change transmission channel
(see Channel Set Up)
NOTE: There are no serviceable parts in the unit, do not attempt to repair it.
Specification
A. Push Button unit
Power
Consumption
: 2 x 3volt Lithium batteries (CR2032 - included, replace with
Byron model SX-100)
: 3.0mA - ON
0.003mA - OFF
B. Door Chime unit
Power
Consumption
Operating Temperature
Operating Distance
Selectable Channel
: 2 x 1.5volt batteries (“D”, R20 or UM1 - not included)
Alternatively powered by A/C-D/C 9volt 300mA
adaptor (Byron model SX-36 - not included)
: 100mA - ON
0.3mA - Stand-by
: -10°C to +40°C
: 100 metres (320 feet approx.) in open field
: Total sixteen (16) possible channels
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Byron SX-15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Byron SX-15 in the language / languages: English as an attachment in your email.

The manual is 0,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info