532522

Byron SX-15 Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
Wire Free Battery Bell Kit
SX-15
The wirefree battery bell kit consists of two
separate units:
1. Push button unit (Transmitter)
2. Door chime unit (Receiver)
These units are completely self-contained
and no wiring between them is necessary.
No wiring is required for this wirfree door bell
kit. When the push button is pressed, it sends
a wirefree signal to activate the door bell.
As the operating range is up to 100 metres
(320 ft. approx.), you can mount the door bell virtually
anywhere in the home, workshop, or office. However,
the operating range of the wirefree signal will be
reduced if the signal is transmitted through a number
of walls or ceilings. Metal, and UPVC doorframes will
also reduce the operating range.
Installation
Push button unit
1. The push button unit is operated by 2 x 3 volt
Lithium batteries (CR2032 - included).
2. Remove the back of the case by pushing in the tab
on the bottom with a small, flat screwdriver.
3. 2 x 3 volt Lithium batteries (CR2032) have been
installed. Simply pull off the isolating strip to allow
the batteries to make electrical contact.
4. Snap the front cover of push button back on and it
is ready to use.
Replacing the batteries. Remove the locking screw
from the battery fastener in the battery compartment.
Insert 2 x 3 volt Lithium batteries (We recommend
Byron model SX-100 - not included), ensure the
battery’s polarity matches the internal markings.
Tighten the screw on the battery fastener to hold the
batteries firm in their compartment. Test to see if the
L.E.D. light comes on.
UM-1
“D”
R20
UM-1
“D”
R20
Installation Guide
a) Bell Push Unit: Using the two holes on the back of push button
as a template,mark the fixing position for the unit. Drill holes,
fit wall plugs (if fixing to masonry) and secure the Bell Push
Unit with screws (self-tapping N3 x 16mm screws - included)
in position, alternatively use the double-sided self-adhesive
pad (included), by placing onto your front doorframe or a
position nearby. Please note, the latter is not the most theft
resistant option.
Important: Mounting the push button unit onto UPVC doorframes
or metal surfaces will reduce the operating range.
b) Door Chime Unit: This has a slotted hang hole on the rear,
this hole will enable the chime unit to be hooked onto a
screw and be easily removed or relocated to another room.
Drill a hole and fit wall plug (if fixing to masonry) and screw (self-tapping N3
x 16mm screw included) to fixing position. Leave a gap of 3mm between the
screw head and the wall. Locate the keyhole slot on the back of the unit over
the screw.
Battery Bell unit
1. Remove the front cover, insert 2 x 1.5 volt alkaline
batteries (“D”, UM1, R20 size not supplied) into the
battery compartment, ensuring the battery polarity
match the internal markings.
2. Snap the front cover back on, the chime unit is ready
to use.
NOT TO BE USED WITH A TRANSFORMER.
Channel Selection
The unit comes from the factory on a pre-set
radio frequency channel. However, should
your door chime activate intermittently for no
reason at all, it is possible that a similar unit
is operating nearby on the same frequency.
The encoded frequency of the push button
(transmitter) and Door Chime (receiver) can
be changed to avoid this problem.
1. Bell Push: Remove the back of the case
by pushing in the tab on the bottom with
a small, flat screwdriver.
Door Chime Unit: Slide open the battery compartment.
2. There is 4 position dip switch marked 1,2,3,4. Use a small screwdriver to
alter the dip switch levers to the “On” or “Off” position, which can be altered
to achieve total sixteen (16) possible channels.
This
way
up
C
R
2
0
3
2
C
R
2
0
3
2
C
R
2
0
3
2
C
R
2
0
3
2
CR2032 x 2
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Byron SX-15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Byron SX-15 in the language / languages: English as an attachment in your email.

The manual is 0,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info