614192
5
Zoom out
Zoom in
Previous page
1/40
Next page
XLf 200 A
5
Voltage supply
We recommend a minimum cross section of 2.5 mm
2
.
Route commercially available plus cables to the battery
and connect via fuse holder.
Use cable glands for holes with sharp edges.
Securely fasten commercially available minus cables to a
noise-free earth point (chassis screw, chassis metal) (not
to the minus pole of the battery).
Scrap the contact surfaces of the earth point until they
are bright and grease with graphite grease.
Connection
; is connected to the positive pole of the
battery and connection : to negative vehicle ground. The
control of the XLf 200 A should ideally be a two-channel con-
trol, either via the preampli er outputs or the loudspeaker
outputs of the car sound system. A control solely via the right
or left channel is also possible since the low-frequency por-
tion of the music is generally identical on both channels.
Integrated fuse
The fuse integrated in the ampli er protects the output stage
and the entire electrical system in case of a malfunction. If a
replacement fuse is used, never bridge fuses or replace them
with a type with higher current.
Audio inputs
You can select between 2 di erent audio inputs;
Cinch (RCA)
Hi level (loudspeaker connections)
Use only one of the audio inputs; otherwise, it may lead to
audio interferences.
The preampli er outputs are connected to the cinch (RCA)
sockets
2 of the subwoofer box via a shielded sound cable.
With control via the loudspeaker outputs, the input connec-
tions of pos.
8/9 are fed to the closest loudspeaker cables
(front or rear) on the left and right. They are separated and
connected to the input connections. The polarity of the
+ or – connections must be observed. Bridge output stages
(BTL) can also be connected directly without an additional
adapter.
Switching on/o
A special feature of the XLf 200 A is its automatic switch-on:
The subwoofer box automatically switches on if a music
signal is received. If no music signal is received for more than
60 seconds, the XLf 200 A automatically switches o .
VOL control
The VOL control 4 is used to adjust the input sensitivity of
the power ampli er to the output voltage of your car sound
system preampli er output.
The adjustment range is from 0.1 V to 7.5 V.
If a car sound system of a third party manufacturer is con-
nected, the input sensitivity must be adjusted corresponding
to the manufacturer data.
A few important explanations in this context:
By turning the control clockwise, the input sensitivity of the
ampli er and, therefore, also the volume increases. However,
this is not a volume control; no further ampli er output
can be achieved in the end position, even if it may sound
like that at the beginning. The system merely increases the
volume faster if the volume control of the car sound system
is turned up.
CROSSOVER frequency control
The CROSSOVER control 5 allows setting the desired entry
frequency.
Example:
At a setting of 150 Hz, the ampli er has a frequency range
of 20 Hz to 150 Hz.
Settings
The following control setting is recommended as basic
setting before putting the device into operation: Sensitiv-
ity (VOL) Pos. 4 to minimum, PHASE Pos. 6 to 0°,  lter
(CROSSOVER) Pos. 5 to approx. 80 Hz. Switch on the device
and select a musical piece with distinctive bass playback.
Increase the volume of your car sound system to the desired
volume level. Now slowly increase the VOL control
4 until
you can hear a clear ampli cation of the bass level. Next,
use the CROSSOVER control 5 to select a  lter setting that
provides a well-contoured bass. You may have to alternately
optimise the sensitivity setting 4 and the  lter setting 5.
A droning bass with excessive volume requires a  lter setting
with a low frequency.
The phase switch
6 must be set so that the bass is inte-
grated into the acoustic pattern as best as possible and not
recognisable as an individual source.
Also check your settings of the XLf 200 A with the bass con-
trol fully open and, if necessary, with activated loudness. An
overloading of the subwoofer box by selecting an excessive
ampli cation (pos.
4) results in a distorted playback and can
damage the loudspeaker.
Power-on indicator (PRT/PWR)
Green LED:
Output stage on, regular operating status.
Red LED:
Output stage is electronically switched o due to an error.
Recycling and disposal
Please use the return and collection systems avail-
able to dispose of the product.
Subject to changes!
BM_XLf200A_22LG.indd.indd 5BM_XLf200A_22LG.indd.indd 5 12.09.2012 11:51:40 Uhr12.09.2012 11:51:40 Uhr
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt Blue Magic XLf 200 A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt Blue Magic XLf 200 A in the language / languages: All languages as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info