586098

Black Decker GX295 T7 Manual

5
Zoom out
Zoom in
Previous page
1/15
Next page
5
ENGLISH
Note: Do not use a spanner or other
implement to tighten the wing nuts.
With the upper and lower handles
assembled, fit the switch box to the upper
handle, as follows:
Note: The switch box must be positioned on
the right-hand side of your mower.
Ensure that the electrical supply cable is
not twisted before you begin to assemble
the handle.
D•Locate the two pins on the switch box (13)
with the holes in the upper handle (12).
•Fit the retaining plate (23) over the stem
of the handle (12) ans secure in position
using the two screws (24) provided.
Note: Do not overtighten these screws - light
pressure will be sufficient to hold the switch
box in position.
•Finally, secure the electrical supply cable
to the lower handle using the cable clip
(17) supplied.
Handle operation (Fig. E)
EThe handle has three positions, two storage
(park) positions and one operating position.
Positions 1 and 3 in Fig. E are the storage
(park) positions and F is the operating range.
For storage purposes, the handle assembly
can be set to position 2 or 3, as follows:
•With the handle in its working range F,
pivot the handle downwards until it
contacts the stops on the end of the
handle tube. This is the park position
2 for the handle.
•The handle can be moved to a park
position 3. Push the handle upwards in
the working range F, to the top position
1. Pull the handle upwards. While still
pulling the handle upwards, pivot the
handle down towards the ground to
position 3.
Height of cut adjustment
Your mower has one height of cut and can not
be adjusted.
Carrying your mower
Disconnect your mower from the mains.
Remove the grassbox (if fitted), lower the handle to
the flat “park” position and then, holding one handle
near the pivot block and carry with the blade pointing
away from you.
How to use your mower (Fig. F & G)
!
Observe all the relevant warnings when
using your mower.
We recommend the directional method of
operation to obtain maximum cutting
performance from your mower and to reduce
the risk of the trailing extension lead from
entering the cutting path.
•Place the bulk of the extension cable
on the lawn close to the starting point
(Fig. Ga position 1).
•Your switch box incorporates a cable
restraint. To fix the cable to the restraint,
proceed as follows:
•Bring the socket end of the extension
cable from behind and connect it to your
mower plug.
F•Form a loop on your extension cable
close to the switchbox.
•Push the loop through the slot from
the opposite side of the restraint hook,
position the loop over the hook and
pull the cable back through the slot.
Your cable will now be restrained.
•The extension cable should now fall
away from your mower and behind the
operator, ready for use.
!
Warning! Do not attempt to operate your
mower with one hand - you must guide it
with both hands.
•Lift the handle up to release it from the
park position.
•Tilt the unit slightly on its side to reduce
the risk of lawn damage whilst starting,
depress the safety lock-off button (15)
on the switchbox (13) (Fig. D), and whilst
still depressed pull the switch lever (14)
towards you. Your mower will start, and
you can now allow it to return to its
proper cutting position, and commence
cutting.
G•Proceed down the cutting area as
shown in Fig. Ga, working from position
1 towards position 2 and, on reaching
position 2, turn to the right and proceed
towards position 3. Continue to the end
of the cutting area, turn to the left, and
proceed towards position 4. Continue in
the same manner as shown in Fig. Ga,
always working away from the cable.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GX295 T7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GX295 T7 in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GX295 T7

Black Decker GX295 T7 User Manual - English, German, Dutch, French, Spanish, Spanish - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info