586098
4
Zoom out
Zoom in
Previous page
1/15
Next page
4
When changing the fuse in your plug,
always ensure the fuse cover is refitted.
If the fuse cover is missing or damaged
do not use the plug.
Note: Fuses do not give personal protection
against electric shock.
Plug replacement
Disconnect the plug from the supply.
Cut off the plug and dispose of
immediately. Insertion of a detached
plug into a 5 amp socket outlet may
result in electric shock.
Only fit BS1363A approved plugs fitted
with the correctly rated fuse.
The cable wire colours, or a letter, will be
marked at the connection points of most
good quality plugs. Attach the wires to
their respective points in the plug (see
below). Brown is for “Live” (L) and blue is
for “Neutral” (N).
Before replacing the top cover of the
mains plug ensure that the cable restraint
is holding the outer sheath on the cable
firmly and that the two leads are correctly
fixed at the terminal screws.
Fit a
BS1363A
approved
plug
Connect blue
to N (neutral)
Make sure that the
outer sheath of the
cable is held firmly
by the clamp
Fit the
recommended
fuse
Connect brown
to L (live)
240 volts AC only.
Never use a light
socket
!
Warning! Never connect live or neutral wires
to the earth pin marked “E” or .
Note: Do not wire an extension cable directly
into your mower yourself. Instead, take your
mower to your nearest Black & Decker
service agent.
Increased safety can be obtained by having
a qualified electrician install a high sensitivity
(30mA) circuit breaker in the house wiring.
If you do not have such a circuit breaker
installed, or you do not wish to have one
installed, then we strongly recommend that
the electrical power to your mower be
supplied through a high sensitivity residual
current device (RCD). The RCD is designed
to provide a high degree of personal
protection against harmful electric current
should fault conditions occur.
!
Warning! The use of an RCD or other circuit
breaker unit does not release the operator of
your mower from the safety instructions and
safe working practices given in this manual.
Handle assembly (Fig. A - D)
ARemove all the parts from the carton and
familiarise yourself with the individual parts of
your mower.
The main parts of your mower are your
mower body (1) which comprises the cutter
cover (2), motor cover (3), air vent shroud (5),
pivot blocks (6) and pivot pins (8).
The handle (10) comprises the lower handle
(11), the upper handle (12), switch box (13)
with switch lever (14) and safety lock-off
switch (15), electrical supply cable (16), the
cable clips (17), and the handle clamp
assemblies (18) which each comprise a wing
nut, washer and bolt.
Note: The electrical supply cable should be
positioned on the right-hand side of your
mower when viewed from the operating
position. Ensure that this is not damaged
or twisted before you begin to assemble
your mower.
Assemble the lower handle to your mower
body, as follows:
BPlace the lower handle (11) into the pivot
blocks (6) on the cutter cover (2).
Note: It will be necessary to tilt the lower
handle towards the rear of your mower to
allow pivot pins (8) to fit correctly.
Fit the pivot pins (8) through the holes in
the pivot block flanges (6) and through
the holes in the lugs on the lower
handle (11).
Using a mallet, or similar tool, tap the
pivot pin (8) through the inner part of the
pivot block (6). The hooks on the end of
the pivot pin will click into position behind
the inner wall, retaining it in position.
Repeat the process on the other side.
With the lower handle in position, assemble
the upper handle, as follows:
CPlace the upper handle (12) over the
lower handle (11).
Align the holes in both the upper and
lower handles and fit a bolt (20) through
each hole. Fit a washer (21) to each bolt
and fit the wing nuts (22) on to the bolts.
Tighten each one with hand pressure only.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GX295 T7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GX295 T7 in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GX295 T7

Black Decker GX295 T7 User Manual - English, German, Dutch, French, Spanish, Spanish - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info