665763

Black Decker GT6530 Manual

6
Zoom out
Zoom in
Previous page
1/88
Next page
6
ENGLISH
Vibration
The declared vibration emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method
provided by EN 60745 and may be used for comparing
one tool with another. The declared vibration emission value
may also be used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual
use of the power tool can differ from the declared value
depending on the ways in which the tool is used.
The vibration level may increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation
of vibration exposure should consider, the actual conditions
of use and the way the tool is used, including taking account
of all parts of the operating cycle such as the times when
the tool is switched off and when it is running idle in addition
to the trigger time.
Labels on tools
The following pictograms are shown on the tool:
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard
Electric safety can be further improved by using a high-
sensitivity 30 mA residual current device (RCD).
Using an extension cable
Always use an approved extension cable suitable for the
power input of this tool (see technical data). The extension
cable must be suitable for outdoor use and marked
accordingly. Up to 30 m of 1.5 mm
2
HO5V V-F extension
cable can be used without loss of product performance.
Before use, inspect the extension cable for signs of damage,
wear and ageing. Replace the extension cable if damaged or
defective. When using a cable reel, always unwind the cable
completely.
Features
1. Front handle
2. Front handle switch
3. Trigger switch
4. Blade
5. Blade sheath
6. Guard
This hedge trimmer has the following features for
your benefit:
Ergonomically formed handles for comfortable cutting.
Machined blades for improved cutting.
Dual action blades for reduced vibration.
Assembly
Warning! Before assembly, make sure that the tool
is switched off and unplugged and that the blade sheath
is fitted over the blades.
Fitting the handle (fig. A)
Slide the handle (1) over the blades (4).
Press the handle (1) into the location on the bottom
of the tool.
Secure the handle with the 4 screws (7) supplied.
Fitting the guard (fig. B)
Locate the guard (6) into the grooves on the tool.
Secure the guard (6) using the two screws (8) supplied.
Warning! Never use the tool without the guard.
Fitting the blade tip guard (fig. C)
An optional tip guard (10) is provided to protect the end of the
blades (4) when cutting near a hard surface.
Align the tip guard (10) with the 2 holes at the end of the
blade support.
Secure the tip guard with the two screws (9) supplied.
Connecting the tool to the mains (fig. D)
Unless the tool is fitted with a mains cable, you will need
to connect an extension cable to the power inlet.
Connect the female socket of a suitable extension cable
to the power inlet of the tool.
Loop the cable through the cable restraint (11) as
shown to prevent the extension cable from becoming
detached during use.
Insert the mains plug into a mains outlet.
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Wear safety glasses or goggles and ear protection
when operating this tool
Wear gloves when operating this tool.
Immediately disconnect the cable from the mains
if it is damaged or cut.
Do not expose the tool to rain or high humidity.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GT6530 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GT6530 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info