633175
4
Zoom out
Zoom in
Previous page
1/4
Next page
Een toetsfunctie voor kanaal 2 toewijzen
De P-toets (programmeertoets) van de ontvanger kort 1.
indrukken.
De led begint op te lichten.
De P-toets nogmaals indrukken.2.
De led dooft even en licht daarna weer op
De gewenste toets van de handzender op. 3 sec. indrukken, 3.
tot de LED uitdooft.
De blauwe led knippert.
De toets weer loslaten en het knipperproces afwachten.4.
Na het knipperproces is de ontvanger klaar voor ontvangst.5.
Programmering controleren
Druk op de geprogrammeerde toets van de zender. f
Het bevel wordt geactiveerd.
Opmerking:
De afstand tussen de zender en de ontvanger moet bij het
De afstand tussen zender en ontvanger moet minstens 1 m
bedragen.
Mocht de zender niet werken moet u opnieuw proberen een
toetsfunctie aan het kanaal toe te wijzen.
De programmeringsprocedure afbreken4.2
Als er tijdens de 60 sec. na het drukken op de P-toets geen
programmering meer volgt, dooft de led van de ontvanger.
Als de P-toets 3 maal na elkaar bediend wordt, dooft de led
van de ontvanger en wordt de programmeringsprocedure
afgebroken.
De aeveringstoestand opnieuw herstellen4.3
Op de P-toets van de ontvanger drukken en deze 1.
gedurende ca. 10 sec. ingedrukt houden.
De led knippert.
Het einde van het knipperproces afwachten en dan de toets
loslaten.
Alle toegewezen handzenders zijn nu gewist.
Opmerking:
Het wissen van afzonderlijke handzenders is niet mogelijk.
Technische gegevens en bijkomende 5
informatie
Toelaatbare omgevingstemperatuur -20˚C tot +60˚C
Max. aantal geheugenplaatsen per
kanaal
50 handzendercodes
Als er meer dan 50 handzendercodes aangeleerd worden,
worden de eerst geprogrammeerde codes gewist.
EG-verklaring van overeenstemming6
De ontvanger BHE324 respectievelijk BHE325 beantwoordt,
op basis van zijn concept en zijn bouwwijze, in de door ons
in omloop gebrachte uitvoering, aan de desbetreende
fundamentele vereisten van de R&TTE-richtlijn 1995/5/EG,
artikel 3.
Toegepaste normen: EN 301 489, EN 300 220.
Rottenburg, 29.2.2008
Fabrikant:
Berner Torantriebe KG,
Graf-Bentzel-Straße 68,
D-72108 Rottenburg
Jürgen Ruppel, Directeur
Asignar una función a un pulsador para el canal 2
Presionar brevemente el pulsador P (pulsador de 1.
programación) del receptor.
El LED se ilumina.
Volver a presionar el pulsador P.2.
El LED se apaga brevemente y, a continuación, vuelve a
brillar
Presionar el pulsador deseado del emisor manual durante 3.
mín. 3 s, hasta que se apague el LED.
El LED azul parpadea.
Vover a soltar el pulsador y esperar a que concluya el 4.
parpadeo.
Después del parpadeo, el receptor está listo para recibir.5.
Comprobar la programación
Presione el pulsador programado del emisor. f
La orden se emite.
Indicación:
La distancia entre el emisor y el receptor debe ser por lo menos
1 m.
Si el emisor manual no funcionara, intente asignar nuevamente
una función al canal.
Interrumpir la programación4.2
Si en el plazo de 60 s desde haber presionado el pulsador
P no se realiza la programación, el LED del receptor se
apaga.
Si se acciona 3 veces consecutivas el pulsador P, se apaga
el LED del receptor y se interrumpe la programación.
Reajustar al estado de suministro4.3
Presionar el pulsador P del receptor y mantenerlo 1.
presionado durante aprox. 10 s.
El LED parpadea.
Esperar a que concluya el parpadeo y volver a soltar el 2.
Esperar a que concluya el parpadeo y, a continuación,
soltar el pulsador.
Todos los emisores manuales memorizados se han
borrado..
Indicación:
No es posible borrar emisores manuales individuales.
Datos técnicos e información adicional5
Temperatura ambiente permitida -20˚C a +60˚C
Número máx. de espacios de
memoría por canal
50 códigos de emisor
manual
Si se memorizan más de 50 códigos de emisores
manuales, se borran los códigos programados en primera
instancia.
Declaración CE de conformidad6
El receptor BHE324 y/o BHE325 corresponden según su
concepto y tipo de construcción en la versión comercializada
por nosotros, a las exigencias básicas pertinentes a la directiva
R&TTE 1995/5/CE, artículo 3.
Normas aplicadas: EN 301 489, EN 300 220.
Rottenburg, 29.2.2008
Fabricante:
Berner Torantriebe KG,
Graf-Bentzel-Straße 68,
D-72108 Rottenburg
Jürgen Ruppel, Gerente
Assegnazione di una funzione per il canale 2
Premere brevemente il tasto P (tasto di programmazione) 1.
del ricevitore.
Il LED si illumina.
Premere nuovamente il tasto P.2.
Il LED si spegne brevemente e si riaccende.
Premere il tasto desiderato sul telecomando per almeno 3.
3 sec., nché il LED non si spenge.
Il LED lampeggia di blu.
Rilasciare il tasto ed attendere che il LED nisca di 4.
lampeggiare.
Dopo il lampeggio il ricevitore è pronto alla ricezione.5.
Verica della programmazione
Premere il tasto programmato del trasmettitore. f
Il comando viene inviato.
Nota:
La distanza fra il trasmettitore e il ricevitore deve essere di
almeno 1 m.
Se il telecomando non funziona, ripetere nuovamente
l‘assegnazione di una funzione tasto al canale.
Interruzione del processo di programmazione4.2
Se nei 60 sec. dopo aver premuto il tasto P non viene
eseguita nessuna programmazione, il LED del ricevitore si
spegne.
Azionando il tasto P per 3 volte consecutive, il LED del
ricevitore si spegne ed il processo di programmazione viene
interrotto.
Ripristina dello stato alla consegna4.3
Premere il tasto P del ricevitore e tenerlo premuto per circa 1.
10 sec.
Il LED lampeggia.
Attendere che il LED non lampeggi più e rilasciare il tasto.2.
Adesso tutti i telecomandi appresi sono stati cancellati.
Nota:
Non è possibile cancellare i singoli telecomandi.
Dati tecnici e informazioni supplementari5
Temperatura ambiente consentita Da -20 ˚C a 60 ˚C
Locazioni in memoria max. per
canale
50 codici telecomando
Se vengono appresi più di 50 codici telecomando, i codici
programmati in precedenza vengono cancellati.
Dichiarazione CE di conformità 6
Il ricevitore BHE324 oppure BHE325, nella struttura, nel tipo
e nella versione da noi messa in circolazione è conforme ai
requisiti fondamentali prescritti nella direttiva R&TTE 1995/5/
CE, articolo 3.
Standard usati: EN 301 489, EN 300 220.
Rottenburg, 29/02/2008
Produttore:
Berner Torantriebe KG,
Graf-Bentzel-Straße 68,
D-72108 Rottenburg
Jürgen Ruppel, Direzione
ESPAÑOL ITA LIA NONEDERL A N DS
Ausgabe / Edition: 04/2008. Änderungen vorbehalten / Subject to change
0682
www.bsr-agenturen.nl
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Berner BHE324 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Berner BHE324 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info