780257
1
Zoom out
Zoom in
Previous page
1/2
Next page
x2
x2
x2
Hardware
WHEEL
GUARD
SET
x2
x1
JUMP SEAT
PAD AND
VELCRO BASE
FOOT PEG SET
x1
D
C
A
B
For Benno® RemiDemi with Jump Seat Rear Rack (Not Included)
REMIDEMI PASSENGER KIT INSTALLATION
READ CAREFULLY BEFORE INSTAL-
LATION AND USAGE. INSTALL AND
USE ONLY AS A COMPLETE KIT.
TO BE INSTALLED BY MECHANIC
AT AUTHORIZED BENNO DEALER.
IMPORTANT: Notes to mechanic: See Instruc-
tions. Install Benno RemiDemi Passenger Kit
only on compatible Benno RemiDemi models in
combination with Benno RemiDemi Jump Seat
Rear Rack. Use only original hardware (included)
and pre-drilled holes and fittings. Do not mount
Passenger Kit to damaged bikes or racks. Do not
modify any parts, racks or bikes, change position
or drill new holes as this will void any warranties
and/or claims for liability.
Step 1: Ensure RemiDemi Jump Seat Rear
Rack (not included) is properly installed and
tightened. (See RemiDemi Jump Seat Rear Rack
Installation Manual).
Step 2: Install Velcro base (B) on Jump Seat
Rear Rack as shown on illustrations (B1-B4).
IMPORTANT: SMALL RED TAB HAS TO BE IN
THE FRONT OF THE RACK.
Pull tabs as tight as
possible while closing the Velcro for a firm and
secure fit to prevent the Velcro base and Jump
Seat Pad from sliding.
Step 3: Line up Jump Seat Pad (A) with Velcro
base (B) and push the pad firmly down onto the
center of the Velcro base.
Step 4:
IMPORTANT:
INSTALL REMIDEMI
WHEEL GUARDS (C) ON BOTH SIDES TO
COVER THE REAR WHEEL.
FAILURE TO DO SO
COULD RESULT IN SERIOUS INJURY!
Ensure all Velcro straps are tightened as shown.
Step 5: Remove rear rubber plug on the lower
tube of the bike frame and install right Foot Peg
(D) into the rear location as shown. Then install
left Foot Peg following the same steps.
After installation, take a short test ride in
order to check for secure fit and ensure that
everything works correctly.
Notes to owner: Periodically check to make sure
all bolts and Velcro straps remain tight as usage
and vibrations may loosen them. ENSURE THAT
BENNO REMIDEMI WHEEL GUARDS REMAIN
ON THE BIKE WHILE CARRYING PASSENGERS.
IMPORTANT: ENSURE THAT
REMIDEMI WHEEL GUARDS
REMAIN ON THE BIKE WHILE
CARRYING PASSENGERS.
IMPORTANT: THE SMALL
RED TAB HAS TO BE IN THE
FRONT OF THE RACK.
IMPORTANT: THE SMALL
RED TAB HAS TO BE IN THE
FRONT OF THE RACK.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benno RemiDemi EVO 1 - Jump seat rear rack at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benno RemiDemi EVO 1 - Jump seat rear rack in the language / languages: English as an attachment in your email.

The manual is 0.28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Benno RemiDemi EVO 1 - Jump seat rear rack

Benno RemiDemi EVO 1 - Jump seat rear rack Installation Guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info