780257
1
Zoom out
Zoom in
Previous page
1/2
Next page
REMIDEMI JUMP SEAT REAR RACK INSTALLATION
IMPORTANT: Notes to mechanic: See Instructions.
Install Benno RemiDemi Jump Seat Rear Rack
only on compatible Benno RemiDemi models.
Use only original hardware (included) and pre-
drilled holes and fittings. Do not mount Jump
Seat Rear Rack to damaged bikes. Do not modify
any parts or bikes, change position or drill new
holes as this will void any warranties and/or
claims for liability.
Step 1: Locate the two black rear rack cross bars
on your RemiDemi.
Step 2: Remove both cross bars by removing
the four nuts and bolts as shown in picture (2).
Save removed cross bars and hardware in case
you are planing to reinstall them in the future.
Step 3: Now install RemiDemi Jump Seat
Rear Rack by inserting all four barrel nuts into
the forward facing holes as shown in picture (3).
Rotate the slots of the barrel nuts into a vertical
position using a flat screwdriver.
Next place a large spacer on each of the four
small platform brackets before lowering rack
down as shown in picture (3).
Step 4: Now insert all four bolts (using the
small washers) from the bottom upwards
through the bracket (and large spacer) into the
rack as shown in picture (4). Carefully hand-
tighten each bolt until you can feel that it has
screwed into the barrel nut. Adjust position
of rack as needed before securely tighten all
four bolts.
Step 5: After installation, take a short test ride
in order to check for secure and tight fit and
ensure that everything works correctly.
Notes to owner: Periodically check to make sure
all bolts remain tight as usage and vibrations
may loosen them.
IMPORTANT:WHEN CARRYING PASSENGERS,
REAR WHEEL MUST BE COVERED!
INSTALL BENNO REMIDEMI WHEEL GUARDS,
SEAT PAD AND FOOT PEGS. FAILURE TO DO
SO COULD RESULT IN SERIOUS INJURY!
For Benno® RemiDemi EVO 1 (Steel Frame Only)
Compatible with:
- Benno City Pannier Bags (RemiDemi Pannier Plates needed)
- Benno RemiDemi Passenger Kit
- Most Racktime®/Snapit® accessories
- Single Yepp® EasyFit baby seat without adaptor
- Other side clamping baby seats (confirm with manufacturer)
- Ortlieb® Pannier Bags with 20mm adapter
(RemiDemi Pannier Plates needed)
Max load: 85lbs/40kg
Dimensions: Deck 18.5cm x 45cm (W x L)
Tubing diameter: 19mm (outside loop)
x4 x4
Hardware
x4 x1
READ CAREFULLY BEFORE INSTALLATION AND USAGE. TO BE INSTALLED
BY MECHANIC AT AUTHORIZED BENNO DEALER.
x4
Barrel
Nut Large
Spacer Small
Washer Bolt Rack
35mm Length
IMPORTANT:
35mm BOLT LENGTH
USE ONLY FOR REMIDEMI EVO 1
(STEEL FRAME)
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benno RemiDemi EVO 1 - Jump seat rear rack at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benno RemiDemi EVO 1 - Jump seat rear rack in the language / languages: English as an attachment in your email.

The manual is 0.27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Benno RemiDemi EVO 1 - Jump seat rear rack

Benno RemiDemi EVO 1 - Jump seat rear rack Additional guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info