660483
7
Zoom out
Zoom in
Previous page
1/11
Next page
7 REFERENCE AMPLIFIER A500 User Manual
(6) CHANNEL INPUT 1 (MONO). Connect the signal source whose output needs
to be amplied.
Please use only one of the three input connectors per channel at any
one time!
Here you will connect an output of your mixing console, your HiFi preamp or
another signal source.
Our rack mixing console EURORACK PRO RX1602, with its eight mono-usable
balanced stereo channels, is an ideal choice for signal processing and
sourceselection.
The connections for both channels are laid out as RCA, XLR and ¼" TRS stereo
connectors. The cinch inputs are intended for use with outputs laid out as
unbalanced signals with a -10 dBV line signal level. Because these inputs
are more sensitive than others, you can directly connect a CD player or a
DAT recorder. Of course this input can also be used for connecting mixing
consoles and similar equipment.
The XLR and ¼" TRS stereo connectors are laid out balanced, but they too can
of course be used to connect unbalanced signals. Their sensitivity is +4 dBu
(also see ch. 4).
Generally speaking, you should choose balanced over unbalanced signals in
order to guarantee the highest noise protection.
Due to safety considerations, the inputs can not be used in parallel.
However,if you are using cinch and XLR or ¼" TRS connectors
simultaneously, the cinch input is given preference, andthe other signal
ismuted.
If you wish to use the A500 in mono-bridged mode,
please only use one of the channel 1 inputs!
(7) CHANNEL INPUT 2. These are the inputs for channel 2.
(8) The STEREO/BRIDGED MONO switch is used to toggle between the two
operating modes of your A500.
Please power the A500 down using the POWER switch each time you
change the operating mode. Similarly, only connect/disconnect speaker
connectors if the A500 has first been powered off!
(9) OUTPUT 1, OUTPUT 2 and BRIDGED MONO: These are the speaker
connectors of your A500 laid out as ¼" TS mono connectors. When in
mono-bridged mode, only use the BRIDGED MONO output.
Keep in mind the minimum power impedance of 4 Ohms per channel
in stereo mode. When in mono-bridged mode, a loudspeaker whose
impedance is at least 8 Ohms must be used.
(10) In addition to XLR or ¼" TRS connectors, you can also use binding posts for
connecting speaker cables. When in mono-bridged mode, make sure to
connect your cables to both middle connectors–as shown on the unit itself.
(11) FUSE SWITCH/VOLTAGE SELECTION. Before connecting the unit to the
mains, please check if the voltage selector corresponds to your local voltage.
When replacing fuses, you should only use fuses of the same type and rating.
With some units, the fuse switch can be put into two dierent positions in
order to select between 230 V and 120 V operation. Please bear in mind:
Ifyou wish to use your equipment outside of Europe running on 120 V,
youwill have to use a fuse with a higher Ampere value.
(12) The mains connection is made via a standard IEC RECEPTACLE. A matching
cable is enclosed.
(13) SERIAL NUMBER.
3. Application Examples
3.1 Stereo mode
In this mode, both channels run independently with a separate input signal.
Connect passive loudspeakers, preferably high-quality studio monitors, such
as the BEHRINGER TRUTH B2031P. Set the STEREO/BRIDGED MONO switch (8)] to
“STEREO” to enable stereo mode.
Please use the POWER switch to power down your A500 before making
any changes to the operating mode settings.
Keep in mind the minimum load impedance of 4 Ohms per channel in
stereo mode.
XENYX 2222FX
Ctrl. Room out
Input
Channel 1
REFERENCE AMPLIFIER A500
Input
Channel 2
TRUTH B2031P
R
L
Fig. 3.1: A500 in stereo operation
Additional examples:
• Two independent mono signals, e.g. instrument signal and monitor mix
• Bi-amp operation, with the bass signal on channel 1 and the treble signal
onchannel 2
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer A500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer A500 in the language / languages: English as an attachment in your email.

The manual is 1,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer A500

Behringer A500 Quick start guide - English - 11 pages

Behringer A500 User Manual - German - 11 pages

Behringer A500 Quick start guide - German - 11 pages

Behringer A500 User Manual - Dutch - 11 pages

Behringer A500 Quick start guide - French, Portuguese, Spanish - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info