Manual Baby Lock Embroidery Professional - BMP8 (page 188 of 238) (English)

661257

188

Zoom out

Zoom in

1/238

Using the Optional Cap Frame 171

Using the Optional Cap Frame

By using the optional cap frame, patterns can be embroidered onto caps and hats. The procedures for using the

cap frame are described below.

Cap frame and its accessories

The cap frame driver and the mounting jig are required in order to use the cap frame.

Memo

●

Before installing the cap frame, be sure to adjust the

ring of the cap frame driver and the height of the L-

shaped bracket. (If the same machine is being used,

this adjustment is only required the first time that it

is used. In addition, this adjustment is not necessary

if the enclosed cap frame is installed.)

●

After the ring of the cap frame driver and the height of

the L-shaped bracket have been adjusted, they must be

adjusted again if a different machine is being used. The

height may differ depending on the machine that is

used. For details, contact your Baby Lock retailer.

Note

● If the cap embroidery frame is attached, the

embroidery frame indicators, showing

which embroidery frames can be used,

appear as shown below.

Cap frame

1 Embroidering area:

50 mm (H) × 130 mm (W)

(2 inches (H) × 5-1/8 inches (W))

2 The mark indicates the center of the

embroidering area.

3 Snap lock

Cap frame driver and 4 thumb

screws

In order to attach the cap frame to

the carriage, remove the

embroidery frame holder, and

then attach this cap frame driver to

the carriage of the machine.

1 Insert the thumb screws into

these holes and tighten the

screws to secure the movable

section. Use these holes when

storing this cap frame driver.

2 Holding Spring

The cap frame is secured by

the two holding Spring.

Mounting jig

Use when framing a cap in the

cap frame.

1 Holders

The cap frame is secured by

the two holders.

2 Mounting bracket

Tighten thumb screw to

secure to mounting surface.

3 Screws

Adjust the size of the

mounting jig according to the

type of cap being

embroidered.

Pad

Allen screwdriver (large) Allen screwdriver (medium)

* Use when adjusting the ring of the cap frame driver and the height of the L-shaped bracket. (Refer to page 175.)

So I’m doing key chains and in order to embroider multiples, I insert one design then merge another and so on. It’s only three colors however I don’t know how to set up the machine to run one color first for all as oppose of the machine doing each one and going through all three colors then the next key chain, all three colors and so on. Do I make sense? Submitted on 3-6-2022 at 06:06
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Embroidery Professional - BMP8 in the language / languages: English as an attachment in your email.

The manual is 10,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Embroidery Professional - BMP8

Baby Lock Embroidery Professional - BMP8 Quick start guide - English, French, Spanish - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Baby Lock Embroidery Professional - BMP8 Manual

Product: