613621
11
Zoom out
Zoom in
Previous page
1/24
Next page
11
Recommendations on use
1/Recommendations on use
There is no point in setting the heating to maximum, the room temperature will not rise any quicker.
When you air the room, switch off the heating by setting cursor A to .
If you will be away for several hours, consider reducing the temperature.
Locking the controls
Wheel B can be locked in position or its range restricted to prevent inappropriate use (by children, etc..).
a) Unhook the device from the wal
l bracket.
b)Detach pins P from their supports on the rear of the control box.
c) Select position N to lock the wheel or position L to restrict its adjustment range.
Select one of the positions M to lock the switch in the desired mode.
Problems Check
The device does not
heat
- Check that the programming unit is in Comfort mode. .
- Check that the premise circuit breakers are triggered or that the load shedder (if you
have one) has not interrupted the device’s power supply.
- Check the air temperature in the room.
The device heats all
the time
- Make sure that it is not in a draft and that the temperature setting has not been chan-
ged. This unit with electronic control is equipped with a microprocessor that can be dis-
tribued by some severe mains voltage disturbances (outside EC standards defi ning the
disturbance protection level). If there are any problems (thermostat blocked, etc.) switch off
the unit power supply (fuse, circuit breaker, etc.) for about 5 minutes to allow the unit to
start again.
The device’s surface
is very hot
It is normal for the device to be hot when it is operating. The maximum surface tempe-
rature is restricted in accordance with the NF Electricité Performance standard. However,
if you think that your device is always too hot, check that the output is suitable for the
area of your room (we recommend 100W / m
2
) and that the device is not placed in a
draught, which would disrupt its setting.
The device does not
follow the program-
ming instructions
- Ensure that you use the programming unit correctly (refer to the instructions manual), that
the programmer is correctly lodged in its housing and that it is operating normally (check
the condition of the batteries).
This device is electronically controlled and its microprocessor can be affected by significant local interferences
(outside the EU norms defining the level of protecton against interference).
If a problem should arise (locked thermostat, etc), cut the power supply to the device (fuse, circuit breaker, etc) for
approx. 10 minutes to reset the device.
If the problem recurs frequently, have your electricity supply checked by your electricity supplier.
2/Maintenance
To maintain the performance of the device, the upper and lower grills must be cleaned with a vacuum clener or
a brush approximately twice per year. Do not use abrasive products.
3/In case of problem
For an absence of :
Less than 2 hours
Do not alter the controls.
2 to 24 hours
Set cursor A to .
More than 24 hours or in summer
Set cursor A to .
GB
16
14
15
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atlantic SOLIUS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atlantic SOLIUS in the language / languages: English, Dutch, French, Spanish as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info