628507

Aspi EF1210 Manual

3
Zoom out
Zoom in
Previous page
1/3
Next page
Application Note: 121 EF1210TEC Addendum
ASPI Digital - The Sound of DSP 3
Systems with More Than Seven Microphones
If more than seven microphones are needed, one or more EF1210s may be added to the system
to provide echo cancellation on each microphone channel. In general, only one EF1210TEC is
needed in the room, and standard EF1210s may be used for additional microphones.
C
ONFIGURING
THE
TEC
The AEC channels of the EF1210TEC can be calibrated and configured as described in the
EF1210 User Manual.
The EF1210TEC may be configured as a standard EF1210 by setting the DIP switch labelled
“Reserved” next to the Device ID 16 DIP switch. When in the off position, the EF1210TEC
behavior will be selected. In the on position, the standard EF1210 behavior is selected.
C
OMMAND
S
ET
C
HANGES
There are three new RS-232 commands in the EF1210TEC. They are TDCD, TDCMIN, and
TDCMAX (the acronym TDC is used because these commands deal with the properties of the
Transmission Delay Compensator as described in the introduction to this addendum). As with
the EF1210, the device type of the EF1210TEC is C.
The TDCD command queries the delay detected by the Transmission Delay Compensator.
This command is used for queries only. For example, the command C00TDCD? queries the
delay detected by the EF1210TEC with device ID 0. The command response contains a delay
value in milliseconds (accurate to within a few milliseconds). If the EF1210TEC were to
return C00TDCD500, the delay detected by the Transmission Delay Compensator is about 500
milliseconds.
The TDCMIN and TDCMAX commands set the minimum and maximum delay over which
the Transmission Delay Compensator will search fo r echoes. Reducing the search range may
cause echoes to be found and cancelled more quickly. For instance, if you know the echo is
delayed somewhere between 600-800 milliseconds, you can set TDCMIN to 500 ms, and
TDCMAX to 1000 ms. This will allow echoes to be found more quickly than if the Transmis-
sion Delay Compensator had to search over the entire 2 second range. It is important not to set
the range too narrowly, because if the delay falls outside of the search range, the TEC will not
be able to cancel echoes. The delay is set in milliseconds. Examples of commands are
C00TDCMIN250 and COOTDCMAX750. The current settings can be queried with a ques-
tion mark as the argument.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aspi EF1210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aspi EF1210 in the language / languages: English as an attachment in your email.

The manual is 0,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Aspi EF1210

Aspi EF1210 User Manual - English - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info