537056

Angelcare AC401 Manual

3
Zoom out
Zoom in
Previous page
1/87
Next page
3
E
N
HOW TO OPERATE YOUR ANGELCARE
®
MONITOR
Charger adapter
socket
STEP 1
Power ON/OFF
Parents unit
pager
Sound volume
UP/DOWN
• Connect the long sensor pad cord into the nursery unit.
• Insert 4 AAA regular batteries (not included) into nursery unit (for battery
backup in case of power failure).
• Connect AC adapter to nursery unit and plug adapter into an electrical
outlet in the baby’s room.
• After both units are properly installed you may adjust the sensor pad
sensitivity level (if necessary).
Note: After each start up, the monitor needs up to 1 minute before the
movement function is ready to be used.
• Once the parents unit is fully charged (after 15 hours) turn the unit ON and
turn the nursery unit ON. If the parents unit is turned ON and the
nurser
y unit is OFF, the parents unit will start beeping after 1 minutes.
After 4 seconds, the unit will shuts itself off.
• The different available options are programmable but you can use
the units right away, with the following factory settings :
- Sound,
movement and tic activated
- Out of range notification OFF
- Voice activated ON
- Temperature display ON, Room temperature control OFF
- Parents unit alarm ON, vibration OFF
- Speaker volume at 3
- Voice sensitivity at 2
• To avoid feedback (whistling sound), keep both units at least 3 meters
apart (10 feet).
• You can adjust the sound volume with the arrow buttons.
• To turn the night light ON, move the right wing button UP.
• Insert 4 AAA NIMH rechargeable batteries (included) into parents unit.
NEVER use regular alkaline batteries.
• Connect AC adapter to parents unit charger and plug adapter into an
electrical outlet. Let charge for 15 continuous hours before using the
monitor for the first time.
Charger adapter
socket
Sensor pad cord
socket
Adapter socket
Sensor pad
sensitivity dial
I sensor pad 2 sensor pads
POSITION OF SENSOR PAD UNDER MATTRESS
Crib center Crib center
• Position the sensor pad as shown above. Make sure the printed side faces up. Do not place any bedding between the mattress and the sensor pad.
• Secure the sensor pad cord to crib using a tie wrap. Run the cord on the floor to ensure it is out of the baby’s reach.
• The sensor pad must rest on a completely flat and rigid surface. Place a 6mm (1/4”) plywood to cover the full size of the crib base. Make sure
the sensor pad’s cord passes underneath the mattress as shown above.
Keep at
least 38 cm
(15 inches)
apart
Sensor Pad(s) 1 or 2
INSTALLATION OF THE SENSOR PAD UNDER THE MATTRESS
STEP 2
INSTALLATION OF THE NURSERY UNIT
Battery
compartment
STEP 3
INSTALLATION OF THE PARENTS UNIT
Battery
compartment
STEP 4
HOW YO USE YOUR ANGELCARE© MONITOR
Power ON/OFF
Movement
capture indicator
(Flashing)
ON/ OFF Night
light button
Power ON indicator
Low battery
indicator
Microphone
Speaker
AC401 international.qxd 6/10/08 11:44 AM Page 3
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Angelcare AC401 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Angelcare AC401 in the language / languages: German, Dutch, Danish, French, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Angelcare AC401

Angelcare AC401 User Manual - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info