792117
3
Zoom out
Zoom in
Previous page
1/16
Next page
User`s Manual
4 / 25
2.
B
UTTONS AND
I
NDICATORS
1. LNB Input: Signal input port for DVB-S. Connects directly to LNB using coaxial cable.
2. Antenna Input: Signal input port for DVB-T and DVB-C. Connect directly to Antenna using
coaxial cable.
3. Charge Light:
Red: the battery is being charged.
Blue: the battery is full.
4. Warn Light: Flash if LNB is short connected
5. Working Light: Green: the meter is in working status
,2
,3
,5
,6
,4
,7
○,10
,9
,8
,12
,11
,1
,13
3
2
13
3
5
7
9
8
11
2. BUTTONS AND INDICATORS
1. LNB Input: Signal input port for DVB-S. Connects directly to LNB using coaxial cable.
2. Antenna Input: Signal input port for DVB-T and DVB-C. Connect directly to Antenna using coaxial cable.
3. Charge Light: Red: the battery is being charged.
Blue: the battery is full.
4. Warn Light: Flash if LNB is short connected
5. Working Light: Green: the meter is in working status
6. Function Keys: F1: Turn on/off the screen display
F2: Enable/disable deep when pressing keys
F3: Enter to TP control menu in Satellite Measure menu
F4: Enter to Auto DiSEqC function in Satellite Measure menu
Note: Press
User`s Manual
5 / 25
6. Function Keys:
F1: Turn on/off the screen display
F2: Enable/disable deep when pressing keys
F3: Enter to TP control menu in Satellite Measure menu
F4: Enter to Auto DiSEqC function in Satellite Measure menu
Note: Press to display help bar on menus to get more information.
7. Navigation Keys:
/
: Move focus or change value.
/: Move focus or change value
8. MENU: Go into main menu or exit from the current menu
9. OK: Confirm
10 . : 1. Turn the meter on/off, press and hold for 2 seconds to power on
the meter.
2. Press to show help bar on each menu.
11. Charging: Connect with the charger cord for charging the equipment.
12. Reset: Reset the meter
13. Screen Display: Show menus and parameters.
3.
H
OW TO MEASURE
Power on the meter, select the system to measure or select system setting to set parameters for the
device in the HOME menu.
In all menus, press [/] button to navigate, press [/] button to change the value of focused
item, press [OK] button to confirm your select, edit value or enter a list to select a wanted item, press
[MENU] button to enter or exit menus.
How to measure satellite signal:
1. Connect the signal cable to F-Type, Female jack.
2. Enter Satellite submenu.
3. Calculate the elevation and azimuth according to your local position in Calculate Angels
menu. Set or adjust your dish to the right position.
4. Set the LNB parameters according to your field environment in LNB Setting menu. Make
sure all the things are correct.
5. Enter to Satellite Measure menu, select the correct satellite and a normal transponder to
check the signal is locked or not.
According to all the output values, such as strength, quality, CNR and power level, you can accurate
your dish to get the best quality signal. And also you can analyzer the signal in Spectrum Chart menu
to display help bar on menus to get more information.
7.
Navigation Keys
:
/
: Move focus or change value.
▼/
: Move focus or change value
8. MENU: Go into main menu or exit from the current menu
9. OK: Confirm
10.
User`s Manual
5 / 25
6. Function Keys:
F1: Turn on/off the screen display
F2: Enable/disable deep when pressing keys
F3: Enter to TP control menu in Satellite Measure menu
F4: Enter to Auto DiSEqC function in Satellite Measure menu
Note: Press to display help bar on menus to get more information.
7. Navigation Keys:
/
: Move focus or change value.
/: Move focus or change value
8. MENU: Go into main menu or exit from the current menu
9. OK: Confirm
10 . : 1. Turn the meter on/off, press and hold for 2 seconds to power on
the meter.
2. Press to show help bar on each menu.
11. Charging: Connect with the charger cord for charging the equipment.
12. Reset: Reset the meter
13. Screen Display: Show menus and parameters.
3.
H
OW TO MEASURE
Power on the meter, select the system to measure or select system setting to set parameters for the
device in the HOME menu.
In all menus, press [/] button to navigate, press [/] button to change the value of focused
item, press [OK] button to confirm your select, edit value or enter a list to select a wanted item, press
[MENU] button to enter or exit menus.
How to measure satellite signal:
1. Connect the signal cable to F-Type, Female jack.
2. Enter Satellite submenu.
3. Calculate the elevation and azimuth according to your local position in Calculate Angels
menu. Set or adjust your dish to the right position.
4. Set the LNB parameters according to your field environment in LNB Setting menu. Make
sure all the things are correct.
5. Enter to Satellite Measure menu, select the correct satellite and a normal transponder to
check the signal is locked or not.
According to all the output values, such as strength, quality, CNR and power level, you can accurate
your dish to get the best quality signal. And also you can analyzer the signal in Spectrum Chart menu
: 1. Turn the meter on/off, press and hold for 2 seconds to power on the meter.
2. Press to show help bar on each menu.
11. Charging: Connect with the charger cord for charging the equipment.
12. Reset: Reset the meter
13. Screen Display: Show menus and parameters.
1
4
6
10
12
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Amiko TSC-1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Amiko TSC-1000 in the language / languages: English as an attachment in your email.

The manual is 2.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info